Results 121 to 130 of about 9,069,962 (304)

Advanced Electron Microscopy and Microcomputed Tomography Analysis of Single‐Crystal Ni‐Base Superalloys After Short‐Term Multiaxial Creep

Advanced Engineering Materials, EarlyView.
This work studies the anisotropic behavior of circular notched tensile specimens of Ni‐base superalloy single crystals during high‐temperature tensile creep along [001], [110], and [111]. Correlative scale‐bridging imaging of specimens reveals early rupture along [110] because 1) plastic deformation proceeds faster at notch center; 2) more (brittle ...
Leonardo Agudo Jácome, Lijie Cao, Christoph Somsen, Johannes Boes, René Hesse, Werner Theisen, Gunther Eggeler   +6 more
wiley   +1 more source

Defect Evolution and Mechanical Performance of Fused Filament Fabrication‐Manufactured 17‐4PH Stainless Steel Revealed by X‐Ray Computed Tomography

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography reveals how process‐induced defects evolve from green to sintered states in Fused Filament Fabrication (FFF)‐manufactured 17‐4PH stainless steel. Internal porosity, weakest cross‐sections, and fracture locations show strong correlation with tensile performance, demonstrating the potential of computed tomography (CT)‐based ...
György Ledniczky, Márk Sárközi, Ibolya Zsoldos, Zoltán Weltsch   +3 more
wiley   +1 more source

Atomic circulation in evanescent of LG10 mode with active dipole and quadrupole transitions

Journal of Taibah University for Science
The total internal reflection of a light with phase singularity, such as Laguerre–Gaussian (LG) light, can generate an evanescent wave. The distribution of this type of light is firmly localized in the vicinity above the dielectric surface and displays a
S. Al-Awfi
doaj   +1 more source

Design and Analysis of Compression–Torsion Coupling Metamaterials Using the Golden Section Method

Advanced Engineering Materials, EarlyView.
A novel compression–torsion metamaterial is engineered using inclined rods and symmetry breaking. To optimize its torsional performance, the golden section method is employed. The mechanical response of the metamaterial is validated through both numerical analysis and experimental validation.
Amirhossein Hassani, Sara Bagherifard
wiley   +1 more source

When Coriolis Matters: Defining Ranges for Lake Upwelling With a New Conceptual Model

Water Resources Research
Historically, two conceptual models for upwelling in stratified lakes have been used. These are the non‐rotational (2D closed basin model) and the coastal model.
Sergio A. Valbuena, Fabián A. Bombardelli, John L. Largier, S. Geoffrey Schladow   +3 more
doaj   +1 more source

Hybrid Metal–Carbon Ink for Printed Stretchable Temperature Sensors

Advanced Engineering Materials, EarlyView.
We prepare conductive inks for temperature sensing with silver flakes and carbon or graphite flakes in a silicone elastomer matrix. Silver dominates the temperature‐dependent conductivity, while the carbon filler network ensures the stability of the conductive pathways and retains function under strain.
Makara Lay, Xue Bai, Thomas Kister, Tobias Kraus   +3 more
wiley   +1 more source

External and Internal Cracking Caused by Heat Treatment in Laser Powder Bed Fusion‐Fabricated Inconel 738LC Components

Advanced Engineering Materials, EarlyView.
Manufacturing problems such as heat treatment‐induced cracking hinder the widespread application of the laser powder bed fusion (LPBF) process to superalloys. In this study, cracks in the LPBF components of Inconel 738LC superalloy are characterized after heat treatment at various temperature ranges, revealing two distinct cracking behaviors.
Kosuke Kuwabara, Masahiro Kusano, Ayako Ikeda, Toshio Osada, Makoto Watanabe   +4 more
wiley   +1 more source

An Investigation on Effective Parameters in Cylindrical Surface Finishing of Hot Resistance Stainless Steel AISI 321 by Magnetic Abrasive Finishing (MAF) Method [PDF]

International Journal of Advanced Design and Manufacturing Technology, 2015
In this study, the three parameters of the abrasive particle size, distance of tool to the work piece, and the rotational speed of cylindrical surface finishing of steel AISI 321 by abrasive particles in the MAF magnetic field was studied. The advantages
Omid Khalilorahmani
doaj  

Additive Manufacturing of Alumina‐Reinforced Elastomers

Advanced Engineering Materials, EarlyView.
Vat‐photopolymerized elastomers reinforced with platelet‐shaped alumina exhibited preferential orientation, reduced porosity, and significantly enhanced mechanical performance. A 3 wt% platelet loading increased tensile strength from 12.4 to 45.7 MPa, highlighting the critical role of filler morphology in elastomeric VPP composites.
Majid Barzegar Keyvani, Zongwen Fu, Robert Göstl, Hamed Shokri, Carmine Putignano, Gianluca Percoco, Bilal Gökce   +6 more
wiley   +1 more source

Extrusion‐Based Additive Manufacturing of Advanced Ceramics: Strengthening Mechanisms and Process Optimization Review

Advanced Engineering Materials, EarlyView.
This review comprehensively evaluates extrusion‐based additive manufacturing for advanced ceramics, detailing feedstock options and key process parameters. By critically addressing defect mechanisms like porosity and cracking, the work highlights optimization strategies through machine learning and advanced postprocessing.
Meisam Bakhtiari, Mohammad Hadi Sheikh‐Ansari, Avinash Borgaonkar, Mehran Dadkhah, Abdollah Saboori   +4 more
wiley   +1 more source