Results 231 to 240 of about 542,523 (285)
Some of the next articles are maybe not open access.
From ERATO Basic Research to the Blue Edge Rotor Blade
Proceedings of the Vertical Flight Society 72nd Annual Forum, 2016In 2015, Airbus Helicopters unveiled the secrecy around its Dauphin successor and presented the all new H160 heli-copter. A special feature immediately attracting attention is its unusual and revolutionary fore-aft swept main rotor blade.
B. G. Wall +10 more
semanticscholar +1 more source
2016
Previous chapters have focused on rotating beams with only the out-of-plane motion. In this chapter, we study rotating blades which have in-plane bending, torsion and axial degrees of freedom. Rotor blades are essential and critical components of helicopters, turbines, compressors and other rotatory machinery (Xiong and Yu, J Sound Vib 302(4–5):821–840,
openaire +1 more source
Previous chapters have focused on rotating beams with only the out-of-plane motion. In this chapter, we study rotating blades which have in-plane bending, torsion and axial degrees of freedom. Rotor blades are essential and critical components of helicopters, turbines, compressors and other rotatory machinery (Xiong and Yu, J Sound Vib 302(4–5):821–840,
openaire +1 more source
Robot for rotor blade inspection
2010 1st International Conference on Applied Robotics for the Power Industry, 2010Rotor blades of wind energy converters are highly stressed components subject to constant load cycles. Regular inspections of rotor blades are indispensible for reliable operation and cost effective production without longer downtimes. Insurers and lenders demand routine inspection of rotor blades every two years.
Norbert Elkmann +2 more
openaire +1 more source
A review of composite rotor blade modeling
29th Structures, Structural Dynamics and Materials Conference, 1988Analyses applicable to composite helicopter rotor blades are reviewed. Important features of such analyses include transverse shear deformation, torsional warping, and nonlinearities associated with large displacement and rotation of the reference cross section.
openaire +1 more source
Performance improvement of a Savonius water rotor with novel blade shapes
, 2021Mabrouk Mosbahi +6 more
semanticscholar +1 more source
Increased Rotor Blade Survivability
1975Abstract : Reported are results of a program to investigate the feasibility of using composite geodesic structure for the blade spar to increase survivability of helicopter main rotor blades. The design investigated consists of a geodesic truss structure spare of elliptical cross section comprised of elements forming a redundant grid-work. This spar is
openaire +1 more source
Journal of the Aeronautical Sciences, 1947
THE PROBLEM of determining bending moments in rotor blades is a fundamental one in the design of rotating wing aircraft. Several methods for solving the problem have been proposed, both empirical and theoretical. In general, the theoretical methods have been so involved that most blade designers have had to take recourse to empirical or semiempirical ...
openaire +1 more source
THE PROBLEM of determining bending moments in rotor blades is a fundamental one in the design of rotating wing aircraft. Several methods for solving the problem have been proposed, both empirical and theoretical. In general, the theoretical methods have been so involved that most blade designers have had to take recourse to empirical or semiempirical ...
openaire +1 more source
1997
Exploiting wind energy has been around since remote times: the Dutch began in 1360 with the typical mill to drain the marshland and for the more traditional agricultural work. In the past 30 years, material technological progress has brought on the construction of aerogenerators that range from an average 100 HP to the American aerogenerator of Grandpa’
DI MARIA, Francesco +2 more
openaire +1 more source
Exploiting wind energy has been around since remote times: the Dutch began in 1360 with the typical mill to drain the marshland and for the more traditional agricultural work. In the past 30 years, material technological progress has brought on the construction of aerogenerators that range from an average 100 HP to the American aerogenerator of Grandpa’
DI MARIA, Francesco +2 more
openaire +1 more source