Results 161 to 170 of about 3,264,220 (298)

Solid‐State Diffusion and Intermetallic Phase Formation in Roll‐Bonded Mg–Zn Composites With Kirigami‐Patterned Inlay

Advanced Engineering Materials, EarlyView.
Mg–Zn composites with a thickness of 0.21 mm were fabricated using roll bonding of a kirigami‐patterned Mg alloy inlay within a Zn matrix. Thermal activation following this process led to the formation of tailored intermetallic structures, which provided the composite with enhanced flexural strength.
Yaroslav Frolov, Oleksandr Bobukh, Christian Klose, Florian Nürnberger, Hans Jürgen Maier   +4 more
wiley   +1 more source

Multiroute pathogen transmission is different. [PDF]

Sci Adv
Scarpino SV.
europepmc   +1 more source

Additive Manufacturing of Continuous Fibre Reinforced Composites: Process, Characterisation, Modelling, and Sustainability

Advanced Engineering Materials, EarlyView.
Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley   +1 more source

Dynamic shift in the dominant transmission route of clade Ib monkeypox virus across networks with sexual and nonsexual contacts. [PDF]

Sci Adv
Miura F, Leung KY, Xiridou M, van Antwerpen M, Low N, Hens N, Vakaniaki EH, Wallinga J.   +7 more
europepmc   +1 more source

Parameter Variation in Planetary Ball Milling of Titanium Aluminide Powder in XHV‐Adequate Atmosphere

Advanced Engineering Materials, EarlyView.
This study investigates the effects of milling parameters, including rotational speed, milling duration, and ball‐to‐powder ratio, on TiAl particle size and morphology in an XHV‐equivalent atmosphere. The creation of oxide‐free surfaces enhances the mechanical properties of green bodies.
Jytte Möckelmann, Armin Piwek, Julius Peddinghaus, Kai Brunotte, Bernd-Arno Behrens   +4 more
wiley   +1 more source

Microstructure Evolution of a VMnFeCoNi High‐Entropy Alloy After Synthesis, Swaging, and Annealing

Advanced Engineering Materials, EarlyView.
The synthesis and processing (rotary swaging and annealing) of the novel VMnFeCoNi alloy is investigated, alongside the estimation of the grain size effect on hardness. Analysis of a wide grain size range of recrystallized microstructures (12–210 µm) reveals a low annealing twin density.
Aditya Srinivasan Tirunilai, Zeki Ayrildi, Buse Şen, Maik Rajkowski, Mathias Redondo Garcia, Markus Stricker, Guillaume Laplanche   +6 more
wiley   +1 more source

High‐Temperature Nanoindentation of Metals: Assessing Thermal Drift, Frame Compliance, and Chemical Composition Effects on the Reported Mechanical Properties

Advanced Engineering Materials, EarlyView.
Do not let thermal drift and instrument artifacts deceive high‐temperature nanoindentation results. We compare classical Oliver–Pharr and automatic image recognition analyses across steels and a Ni alloy to quantify these effects. Accounting for artifacts reveals systematic softening with temperature, while Cr and Ni additions boost resistance ...
Velislava Yonkova, Steffen Brinckmann, Ruth Schwaiger   +2 more
wiley   +1 more source

Limb apraxia and active inference in the visuomotor pathways. [PDF]

Psychon Bull Rev
Proietti R, Pezzulo G, Binkofski F, Tessari A.   +3 more
europepmc   +1 more source

Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites

Advanced Engineering Materials, EarlyView.
Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter, Andreas Bezold, Johan Westraadt, Katharina Fiegl, Subham Chattoraj, Benjamin Wahlmann, Carolin Körner, Michael Mills, Mathias Göken, Steffen Neumeier   +9 more
wiley   +1 more source

Employing in-context learning prompts with large language models for drone routing in delivery services. [PDF]

PLoS One
Masoud M, Elhenawy M, Abdelhay A.
europepmc   +1 more source