Results 271 to 280 of about 584,553 (309)

A method for rubber toughening powder coatings

Polymer Bulletin, 1993
This paper describes a new method for rubber toughening brittle powder coatings. The design involves the use of toughening agents with specific physical and chemical properties. The modifiers are low-to-medium molecular weight polymers with polymerizable end groups (macromonomers).
J. L. Hedrick, R. D. Allen, A. Diaz, J. G. Hilborn, J. C. Hedrick   +4 more
openaire   +1 more source

Rubber Powder – A Perspective Filler of Thermoplastics

Macromolecular Symposia, 2005
AbstractRubber powder, ground at ambient temperature, was compounded with polypropylene using only 16 L/D of a co‐rotating twin screw extruder. An optimum of extruder configuration and selected process parameters were found for compounds with a rubber filling rate of 50 wt.‐%. Restrictions of a reactive compounding were taken into account.
Udo Wagenknecht, Stefanie Steglich, Sven Wiessner, Hannes Michael   +3 more
openaire   +1 more source

Structural and dynamic microheterogeneity of rubber powder

Russian Journal of Physical Chemistry B, 2009
Spin probe EPR spectroscopy was used to study the local dynamics of vulcanizates of an ethylenepropylene-diene elastomer and rubber powders prepared from them. It was revealed that the preparation of rubber powders is accompanied by the formation of a polymer network with an essentially nonuniform local structure.
O. P. Kuznetsova, D. A. Khalilov, I. I. Aliev, B. V. Yastrebov, A. M. Vasserman, E. V. Prut   +5 more
openaire   +1 more source

Analysis on Modifying Asphalt by Rubber Powder

Key Engineering Materials, 2013
This article by groups of comparison, analyzes the impact of he content, the mesh size and the kinds of Rubber Powder to Modified asphalt properties. Experiments concluded that, the content of rubber powder has the most impact to rubber powder modifying asphalt properties, and when the content in 10%～20% has a optimal value; the mesh size is not the ...
Hui Guang Bian, Yu Jian Wu, Chuan Sheng Wang   +2 more
openaire   +1 more source

Characterization of composites based on chlorosulfonated polyethylene rubber/chlorinated natural rubber/waste rubber powder rubber blends

Journal of Thermoplastic Composite Materials, 2013
Chlorosulfonated polyethylene rubber (CSM) was blended with chlorinated natural rubber (CNR) with various formulations and blend ratios (CSM/CNR: 100/0; 75/25; 50/50; 25/75; 0/100) keeping the total waste rubber powder (WRP) content constant at 50 phr (parts per 100 rubber).
Marković, Gordana, Marinović-Cincović, Milena, Jovanović, Vojislav, Samaržija-Jovanović, Suzana, Budinski-Simendić, Jaroslava K.   +4 more
openaire   +2 more sources

Characterization of New Rubber Compounds with Incorporation of Recycled Rubber Powders

Materials Science Forum
The global growth of discarded end-of-life tires (ELT) is leading to a significant challenge of waste management. Many of these tires are incinerated or exported to countries with less stringent environmental regulations, exacerbating pollution and wasting resources.
Nuno Soares Domingues, Luís Monteiro Gonçalves   +1 more
openaire   +1 more source

Effect of Recycled Rubber Powder on the Compatibility of Rubber-Cement Paste

Annales de Chimie - Science des Matériaux, 2022
Layachi Guelmine, Deboucha Sadek, Hadda Hadjab, Amar Benazzouk   +3 more
openaire   +1 more source

Grafting waste rubber powder and its application in asphalt

Construction and Building Materials, 2021
Xiaoping Wang
exaly  

Powdered rubber-filler batches

Composites Theory and Practice, 2002
Adam Tarniowy, Eulalia Grabowska
openaire   +1 more source

Powdered Rubber Waste in Rubber Compounds

2005
Ceni Jacob, S De
openaire   +1 more source