Results 41 to 50 of about 2,183,981 (341)
The effect of joint width between blocks in concrete block pavement [PDF]
, 2006 Jointing sand is the main component of concrete block pavement (CBP) that promotes load transfer between blocks. Often, when sands are available from various sources, it becomes a difficult task to judge the right source of sand.
Ling, Tung Chai +2 more
core
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Mechanical properties of the concrete containing porcelain waste as sand [PDF]
, 2018 The demand of concrete have been increases on a daily bases which consume a lot of natural resource such as sand and gravel, there is an immediate need for finding suitable alternative which can be used to replace sand partially with another materials ...
Al-juboor, Shihab +4 more
core +1 more source
Advanced Engineering Materials, EarlyView.It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti +11 more
wiley +1 more source
A Quasi-Variational Inequality Problem Arising in the Modeling of Growing Sandpiles [PDF]
, 2012 Existence of a solution to the quasi-variational inequality problem arising in a model for sand surface evolution has been an open problem for a long time.
Barrett, John W., Prigozhin, Leonid
core +1 more source
Effect of Laser Deoxidation on Adhesive‐Bonded Aluminum in an Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.This study investigates laser ablation of aluminum under oxygen‐free conditions. The goal is to produce oxide‐free substrates that enable improved adhesive bonding with epoxy. Optimized laser parameters (90% overlap, 300 µJ) combined with oxide‐free substrates result in the highest tensile strength of the adhesive bond.
Sandra Gerland +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.A combined finite element and phase‐field approach predicts the evolution of microstructure during the directional solidification of Ni‐based superalloys. The model reveals how withdrawal rate, temperature gradient, and wall thickness control the dendrite spacing, highlighting the strong effect of surface regions in thin sections where dendrite growth ...
Sean Böhm +3 more
wiley +1 more source
Removing Oxide Layers and Retaining Oxide‐Free Steel Surfaces by Polishing in Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.In this study, the efficacy of wet mechanical polishing under an oxygen‐free atmosphere for deoxidation and the retention of an oxide‐free steel surface are elucidated using X‐ray photoelectron spectroscopy. The methodology proved successful; however, the results were highly dependent on the preparation of the solvents used to clean the samples after ...
Friedrich Bürger +2 more
wiley +1 more source
XRootD S3 Gateway for WLCG Storage [PDF]
EPJ Web of ConferencesThe S3 Gateway is a server based application that provides a bridge between protocols and security used in the HEP community to S3 protocols and its associated security model.
Hanushevsky Andrew, Yang Wei
doaj +1 more source
Food & Nutrition Research, 2023 Background: Nutritional interventions may serve as a stress resilience strategy with important implications for human health. Objective: The aim of this study was to investigate the effect of vitamin D supplementation throughout wintertime on problem ...
Anita L. Hansen +8 more
doaj +1 more source