Results 31 to 40 of about 115,094 (305)
Assessment Method of Overheating Degree of a Spent Moulding Sand with Organic Binder, After the Casting Process [PDF]
, 2013 A proper management of sand grains of moulding sands requires knowing basic properties of the spent matrix after casting knocking out. This information is essential from the point of view of the proper performing the matrix recycling process and ...
Dańko R.
core +1 more source
The capability enhancement of aluminium casting process by application of the novel CRIMSON method [PDF]
, 2011 The conventional foundry not only frequently uses batch melting, where the aluminium alloys are melted and held in a furnace for long time, sometimes as long as a complete shift, but also uses the gravity sand casting process where the molten aluminium
Dai, Xiaojun +2 more
core +1 more source
Pengaruh Variasi Campuran Bentonit Terhadap Karakteristik Pasir Cetak Untuk Proses Sand Casting
Rekayasa, 2022 The casting process is widely used because it has the advantage of being able to make products with small dimensions to very large dimensions, the use of materials is more efficient, the casting products can be directly used.
Apang Djafar Shieddieque +3 more
doaj +1 more source
Impact of the Different Moulding Parameters on Properties of the Green Sand Mould [PDF]
Archives of Foundry Engineering, 2023 Sand Casting process depends mainly on properties of the green sand mould, sand casting requires requires producing green sand mould without failure and breakage during separation the mould from the model, transportation and handling.
Dheya Abdulamer
doaj +1 more source
Relationship between casting modulus and grain size in cast A356 aluminium alloys [PDF]
, 2012 Microstructure of Al-Si alloy castings depends most generally on melt preparation and on the cooling rate imposed by the thermal modulus of the component. In the case of Al-Si alloys, emphasis is put during melt preparation on refinement of pro-eutectic (
+22 more
core +4 more sources
Application of Non-Silica Sands for High Quality Castings [PDF]
Archives of Metallurgy and Materials, 2020 The goal of this article is to application of non-silica sands based on alumininosilicates as an alternative of traditionally used chromite sand for alloyed steel and iron castings.
J. Beňo, M. Poręba, T. Bajer
doaj +1 more source
Sand-Casting Technique for Trans-Tibial Prostheses [PDF]
Prosthetics & Orthotics International, 2005 A sand-casting technique for trans-tibial sockets was applied to 28 amputees, and the prosthetic fit observed through transparent check sockets. The results were better than historical reports of fittings with plaster of Paris casting by qualified prosthetists.
J Steen, Jensen +2 more
openaire +2 more sources
Journal of Mechanical Engineering Science and Technology, 2018 Casting is one of method that used in forming the work piece by melting specific metal and pouring into moulding that has been prepared. This study aimed to determine the effect of the use of Bangkalan clay as binder in sand moulding against tensile ...
Imam Muhtarom, Sunomo Sunomo
doaj +1 more source
THE CHARACTERISTICS OF LAMPUNG LOCAL SAND AS CASTING SAND IN THE METAL CASTING PROCESS [PDF]
Jurnal Dinamika Penelitian Industri, 2019 In Indonesia, the demand for sand was mainly fulfilled using sand brought from Java although with a very expensive transportation cost. For the Sumatran region, the province of Lampung is rich in quartz sand that has the potential to act as substitute to the Java originated sand.
Yusup Hendronursito +5 more
openaire +1 more source
Frontiers in Public Health, 2023 IntroductionTo investigate the major existing occupational hazards and to assess the occupational health risks for ferrous metal foundries (FMFs) in Ningbo, China.MethodsUnified questionnaires were formulated to investigate the information on the basic ...
Donghui Duan +5 more
doaj +1 more source