Results 31 to 40 of about 51,052 (215)
Self‐Cleaning Sensor Surfaces for Long‐Term Environmental Monitoring
Advanced Engineering Materials, EarlyView.Long‐term use of unattended outdoor sensors without soiling or biofouling is achieved through generation of a micro‐ and nanorough cuvette surface by combing hydrophobic nanoparticles with fluorinated polymers, crosslinked and surface‐attached through CHic chemistry. The coating demonstrates self‐cleaning behavior and prolonged outdoor stability, which
Sanam Kumari Rajak +4 more
wiley +1 more source
X-Sand Filter: An X-Tolerant Response Compaction Technique for Faster-Than-At-Speed Testing
Mehran University Research Journal of Engineering and Technology, 2020 Faster-than-at-speed testing provides an effective way of detecting small delay defects but at the cost of increased number of unknown logic values on longer paths of the circuit under test.
Salman Ahmad, Kashif Iqbal
doaj +1 more source
A Creep Prediction Model for Concrete Made from Pit Sand with Low Silica Content
Infrastructures, 2022 Pit sand generally has a lower silica content than sand sourced from rivers or crushed stones. The effect of this sand on the creep of concrete has not yet been fully studied.
Daud Andang Pasalli +2 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Despite benefits to storage stability and handleability of aluminum scrap, octadecyl phosphonic acid (ODPA) SAMs reduce the tensile strength of wires produced using friction‐induced recycling. Etching and methyl diphosphonic acid (MDPA) coatings, however, have little effect.
Timothy D. Goller +3 more
wiley +1 more source
Investigation of the Sand Porosity via Oedometric Testing
The Baltic Journal of Road and Bridge Engineering, 2010 Investigation of the porosity of Klaipėda sand by oedometric test is presented. The Klaipėda sand is typical Baltic see-shore sand consisting of grains the average diameter of which varies from 1.18 mm to 0.3 mm.
Jonas Amšiejus +3 more
doaj +1 more source
Advanced Functional Materials, EarlyView.This study advances SafeWax, a bio‐inspired, fatty‐acids‐based superhydrophobic coating, by identifying an agriculturally compliant solvent and revealing how solvent‐controlled Fatty acid crystallization governs the coating's microscopic structure and performance.
Niv Ben‐Arie +13 more
wiley +1 more source
Thermal reclamation of the used moulding sands
Metalurgija, 2015 The paper presents the results of the research on the used moulding sands subjected to mechanical and thermal reclamation at different stages of the process in the foundry.
M. Łucarz
doaj
Study on Process Mineralogy and Selectivity of a Quartz Sand in Shaanxi Province
Kuangchan zonghe liyong, 2022 It is beneficial to conduct mineralogy research on the abundant quartz sand resources located in Shaanxi Province, thereby providing high value and efficient utilization methods.
Qihang Xiao, Yubiao Li, Qizhou Tang
doaj +1 more source
Advanced Functional Materials, EarlyView.An Alhagi maurorum inspired hierarchical composite membrane (NFCu) was developed by integrating heavy metal remediation and solar‐driven interfacial evaporation in a single platform. Beyond the photothermal effect, a localized photocatalytic process is realized on the CuO surface, deepening the mechanistic understanding of light–matter–water ...
Yuqiong He +9 more
wiley +1 more source
Sand Goby—An Ecologically Relevant Species for Behavioural Ecotoxicology
Fishes, 2018 Locomotion-based behavioural endpoints have been suggested as suitable sublethal endpoints for human and environmental hazard assessment, as well as for biomonitoring applications.
Davide Asnicar +5 more
doaj +1 more source