Results 121 to 130 of about 699,469 (306)

The potential role of photoelectron microscopy in the analysis of biological surfaces [PDF]

open access: yes, 1984
12 pagesThe photoelectric effect provides the basis for an imaging technique useful for the study of biological surfaces. The photoelectron microscope (PEM) employs a UV lamp to photoeject electrons from the specimen surface.
Jost, P. C.   +2 more
core  

Creep‐Induced Microstructural Evolution in an A2‐B2 Superalloy

open access: yesAdvanced Engineering Materials, EarlyView.
A 27.3Ta‐27.3Mo‐27.3Ti‐8Cr‐10Al (at.%) refractory high‐entropy alloy with precipitation‐strengthened A2‐B2 microstructure was studied by creep tests at 1030°C, which demonstrate a transition in deformation mechanisms in the range of 100–150 MPa applied stress. This is associated with changes in dislocation–precipitate interactions. Relevant deformation
Liu Yang   +10 more
wiley   +1 more source

Scanning electron microscopy of human metaphase chromosomes [PDF]

open access: yes, 1986
Preparative methods for scanning electron microscopy of chromosomes are dependent on the original source of material. Chromosomes extracted from unfixed metaphase cells via isolation buffers tend to show topography and surface morphology which may have ...
Claugher D   +3 more
core  

Scanning electron microscopy in the tests of fibre-cement boards

open access: yesMATEC Web of Conferences, 2018
The subject of this article is research on fiber-cement boards, which are currently used in civil engineering as cladding for ventilated facades, but also as internal claddings.
Adamczak-Bugno Anna   +2 more
doaj   +1 more source

Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A

open access: yesAdvanced Engineering Materials, EarlyView.
The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han   +5 more
wiley   +1 more source

Combining confocal and BSE SEM imaging for bone block surfaces [PDF]

open access: yes, 2005
The present report presents a method for the correlation of qualitative and quantitative BSE SEM imaging with confocal scanning light microscopy (CSLM) imaging modes applied to bone samples embedded in PMMA.
Zamecnik, J, Lovicar, L, Boyde, A
core  

Recycling of NiTi Shape Memory Alloys: Fundamental and Technological Aspects of a Vacuum Induction Melting Processing Route

open access: yesAdvanced Engineering Materials, EarlyView.
The present study investigates recycling of NiTi shape memory alloys via vacuum induction melting. An ingot was synthesized from elemental Ni and Ti and subjected to three subsequent remelting cycles. Remelting increases process durations and impurity levels and adversely affects microstructures and functional properties.
Sakia Sophia Noorzayee   +7 more
wiley   +1 more source

Current Status and Challenges in Data Collection for Aerospace Coatings Deposited by Plasma Spraying

open access: yesAdvanced Engineering Materials, EarlyView.
An innovative approach has been integrated into the GRENAT project to optimize plasma spraying and coating performance. Raw materials are accelerated and melted in the plasma generated by torches, creating coatings. Monitoring sensors collect process data which are combined with ex situ characterization data.
Lila Randriamananjara   +8 more
wiley   +1 more source

Combining Scanning Probe Microscopy and Transmission Electron Microscopy [PDF]

open access: yes, 2011
This chapter is a review of an in situ method where a scanning electron microscope (SPM) has been combined with a transmission electron microscope (TEM).
Nafari, Alexandra,   +4 more
core  

In Situ Micromechanical Study of Bimodal γ′–γ″ Precipitate Assemblies in Ni–Cr–Al–Nb Superalloy

open access: yesAdvanced Engineering Materials, EarlyView.
A Ni–Cr–Al–Nb superalloy with a bimodal γ′–γ″ precipitate distribution is developed. Composite precipitate assemblies form through heterogeneous nucleation, effectively impeding dislocation motion. Micropillar compression reveals high strength at room and elevated temperatures, governed by precipitate shearing, with coupled faulting mechanisms ...
Ujjval Bansal   +4 more
wiley   +1 more source

Home - About - Disclaimer - Privacy