Results 161 to 170 of about 2,240,629 (329)

Enhanced Oxidation and Thermal Shock Resistance of N‐type Mg2Si0.89(Sn0.1,Sb0.01) Thermoelectric Material via Cr0.9Si0.1 Coating

Advanced Engineering Materials, EarlyView.
Cr0.9Si0.1 protective coatings are developed to enhance the thermal‐shock and oxidation resistance of Mg2Si0.89(Sn0.1,Sb0.01) thermoelectric (TE) materials. The coating forms a dense and adherent barrier that suppresses oxygen diffusion and mitigates mechanical degradation during cyclic oxidation, demonstrating its potential to improve the long‐term ...
Mikdat Gurtaran, Zhenxue Zhang, Xiaoying Li, Hanshan Dong   +3 more
wiley   +1 more source

Advancing two‐component partitioning of light scattering in C ayuga L ake, N ew Y ork [PDF]

, 2015
Feng Peng, Steven W. Effler
openalex   +1 more source

Microstructural Evolution and Mechanical Performance of Plasma‐Assisted Hybrid Friction Stir Welded Dissimilar Aluminum–Copper Joints

Advanced Engineering Materials, EarlyView.
Plasma‐assisted hybrid friction stir welding of dissimilar AlCu joints employs localized plasma preheating to balance heat input and enhance plastic flow. The optimized process reduces axial force by up to 35%, refines the microstructure, and achieves ≈96% joint efficiency.
Deepak Kumar Yaduwanshi, Pankaj Shrivastava, Ganesh Chouhan, Velaphi Msomi   +3 more
wiley   +1 more source

Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6

Advanced Engineering Materials, EarlyView.
The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter, Thomas Wegener, Andreas Schilling, Martin Fehlbier, Thomas Niendorf   +4 more
wiley   +1 more source

Investigation of the spatial profile of stimulated Raman scattering beams in D2 and H2 gases using a pulsed Nd:YAG laser at 266 nm

, 2004
Stelios Tzortzakis, G. Tsaknakis, Alexandros Papayannis, A. A. Serafetinides   +3 more
openalex   +1 more source

Proton-Nucleus Scattering at Medium Energies [PDF]

, 1974
J. Saudinos, C. Wilkin
openalex   +1 more source

Can Ti‐Based MXenes Serve as Solid Lubricants for Brake Applications? A Tribological Study

Advanced Engineering Materials, EarlyView.
This study explores the first implementation of Ti‐based MXenes materials in brake pad friction composite material. The resulting composite material exhibits a 48% reduction in the wear rate; alongside significant improvements are observed for thermal and mechanical properties.
Eslam Mahmoud, Jakob Gruber, Hakan Göçerler, Pierluigi Bilotto, Christian Gierl‐Mayer, Elham Loni, Michael Naguib, Carsten Gachot   +7 more
wiley   +1 more source

Assessment of deformation of human red blood cells in flow cytometry: measurement and simulation of bimodal forward scatter distributions

, 2019
Jonas Gienger, Hermann Groß, Volker Ost, Markus Bär, J. Neukammer   +4 more
openalex   +1 more source

The semiclassical and quantum regimes of super-radiant light scattering from a Bose–Einstein condensate [PDF]

, 2005
G. R. M. Robb, N. Piovella, R. Bonifacio
openalex   +1 more source

Interaction between Molten Al‐Killed Mn–B Steel and Carbon‐Bonded MgO Refractories Based on Recyclates

Advanced Engineering Materials, EarlyView.
High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé, Lukas Neubert, Anton Yehorov, Till M. J. Stadtmüller, Christos G. Aneziris, Olena Volkova   +5 more
wiley   +1 more source