Results 151 to 160 of about 1,942,037 (303)

Habitat Loss Through Renewable Energy Infrastructure: Budgeting the Energetic Consequences for Wintering Geese. [PDF]

Environ Manage
Vergin L, Madsen J, Linssen H, Nolet BA, Clausen KK.   +4 more
europepmc   +1 more source

Distinct Microstructural Characteristic Lengths Defining Notch Fatigue Crack Initiation and Propagation, and Defect Tolerance in Advanced Steels

Advanced Engineering Materials, EarlyView.
Schematic representation of modes of microcrack nucleation, growth and temporary arrestment at different boundaries, with the criteria for crack propagation in three scenarios: (1) large notch, (2) defect/small sharp notch, and (3) long crack. This work revisits and integrates results on the fatigue behavior of advanced bainitic steels (in particular ...
Lucia Morales‐Rivas
wiley   +1 more source

Coupling Hydrological Scenarios and Water Footprints for Multi-Objective Cropping-Structure Optimization in the Middle and Lower Shiyang River Basin. [PDF]

Plants (Basel)
Pu Y, Qi G, Zhang Y, Kang Y, Wang Y, Tang Z, Dang H, Yang F, Fu D.   +8 more
europepmc   +1 more source

Integration of OpenCV‐Based Microscopic Adhesive Volume Measurement Into a Pyiron Workflow for Automated Data Analysis

Advanced Engineering Materials, EarlyView.
Residual adhesive after electrode loading in adhesive‐assisted resistance spot welding is quantified through a traceable experimental‐to‐digital workflow. Chromatic confocal topography provides calibrated surface‐height data, while OpenCV detects the electrode imprint and integrates adhesive height into comparable volume metrics.
Sung‐Min Wi, Jiangdong Zhao
wiley   +1 more source

Lost in Projection: Uncertainty is Misrepresented in Climate Risk and Vulnerability Assessments. [PDF]

Risk Anal
Curran P, Hardaway K, Logan T.
europepmc   +1 more source

Superlubricity and Corrosion Inhibition Properties of Solvate Ionic Liquids in Hybrid Carbon Fiber Reinforced Plastic–Steel Interfaces

Advanced Engineering Materials, EarlyView.
Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees, Timothy Harte, Bhagya Dharmasiri, Y. Athulya Wickramasingha, David J. Hayne, Daniel J. Eyckens, Luke C. Henderson   +6 more
wiley   +1 more source

Impact Assessment of Emissions Stabilization Scenarios with and without Induced Technological Change [PDF]

The main aim of this paper is to investigate quantitatively the economic impacts of emissions stabilization scenarios with and without the inclusion of induced technological change (ITC).
Claudia Kemfert, Truong P. Truong
core  

Near-term increased exposure to political risk for African power trades. [PDF]

Nat Commun
Bonserio T, Carlino A, Giuliani M, Castelletti A.   +3 more
europepmc   +1 more source

Model‐Guided Design of Paper Membrane Architectures for Controlled Flow and Enhanced Diagnostic Sensitivity

Advanced Engineering Materials, EarlyView.
Geometrical modifications on nitrocellulose membranes can result in observable differences in signal intensity relative to a reference membrane (top and bottom left). Using two reference experiments, we have developed a theoretical model that can reproduce the experimentally observed flow changes and provide information on membrane parameters, e.g ...
Maria Dimaki, Lea Holritz, Winnie E. Svendsen   +2 more
wiley   +1 more source

Simulation Study of the Decision Logic for 95% Upper Confidence Limit Calculations Applied in ProUCL 5.2. [PDF]

Risk Anal
Stuchal LD, Hutton S, Remmer C, Goodkind N, Goodrum P.   +4 more
europepmc   +1 more source