Results 111 to 120 of about 115,255 (264)

Precipitation Simulations of the O‐Phase in Ti2AlNb Alloys Processed by Laser Powder Bed Fusion

open access: yesAdvanced Engineering Materials, EarlyView.
Simulated and experimental evolution of the O‐phase volume fraction during postprocessing of a Ti‐21Al‐25Nb (at.%) alloy processed by laser powder bed fusion. With results of sensitivity to input parameters from a thorough and quantified analysis, the interfacial energy matrix/precipitate is the most relevant input parameter for the simulation of the O‐
Silvana Tumminello   +7 more
wiley   +1 more source

Feasibility of Nitrogen as a Carrier Gas for Inconel Cold Spray in Hydropower Application

open access: yesAdvanced Engineering Materials, EarlyView.
N2, despite being nearly two orders of magnitude cheaper than He, is a feasible carrier gas for cold spray Inconel coatings in hydropower repair applications when higher gas temperature and pressure are used. Reducing powder size significantly improved cavitation resistance, while the addition of fine chromium carbide particles further enhanced erosion
Tianhao Wang   +4 more
wiley   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

open access: yesAdvanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal   +3 more
wiley   +1 more source

Active Corrosion Protection of Sintered AA7075 Aluminum Alloy via Mn Powder Addition

open access: yesAdvanced Engineering Materials, EarlyView.
AA7075 containing Mn‐rich particles is fabricated via spark plasma sintering using AA7075 and Mn powders. Corrosion resistance is evaluated through dip‐and‐dry tests using 0.1 M NaCl (pH 6.0), and mass loss decreases with increasing Mn addition. Mn‐rich particles function as a source of Mn ions, and formation of Mn‐accumulation films on Cu‐containing ...
Ko Ebina, Masashi Nishimoto, Izumi Muto
wiley   +1 more source

DigiChrom: A Domain Ontology for Semantic Representation of Trivalent Chromium Platings and Its Large Language Model‐Based Alignment With Multiple Mid‐Level Ontologies

open access: yesAdvanced Engineering Materials, EarlyView.
Digitalizing electroplating requires both domain knowledge and interoperability. This work introduces PlatOn, a domain ontology for trivalent chromium plating and coating characterization, and a hybrid pipeline that aligns it to a mid‐level reference ontology by combining eight similarity metrics with language model reasoning. Expert‐validated mappings
Janik Harter   +10 more
wiley   +1 more source

Extrusion‐Based Additive Manufacturing of Advanced Ceramics: Strengthening Mechanisms and Process Optimization Review

open access: yesAdvanced Engineering Materials, EarlyView.
This review comprehensively evaluates extrusion‐based additive manufacturing for advanced ceramics, detailing feedstock options and key process parameters. By critically addressing defect mechanisms like porosity and cracking, the work highlights optimization strategies through machine learning and advanced postprocessing.
Meisam Bakhtiari   +4 more
wiley   +1 more source

On the Effect of Creep on Local Lattice Orientation in Single‐Crystal Ni‐Based Superalloy Microstructures

open access: yesAdvanced Engineering Materials, EarlyView.
During creep of a single‐crystal Ni‐based superalloy, the overall crystal orientation is observed to remain constant while the microstructure evolves. Despite the lack of macroscopic rotation, small (<1°) rotations are observed on the submicron size scale and are accommodated by counteracting rotations over the scale of several micrometers.
E. J. Payton   +3 more
wiley   +1 more source

Superlubricity and Corrosion Inhibition Properties of Solvate Ionic Liquids in Hybrid Carbon Fiber Reinforced Plastic–Steel Interfaces

open access: yesAdvanced Engineering Materials, EarlyView.
Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees   +6 more
wiley   +1 more source

Intermediate Resistive State in Wafer‐Scale Vertical MoS2 Memristors Through Lateral Silver Filament Growth for Artificial Synapse Applications

open access: yesAdvanced Functional Materials, EarlyView.
In MOCVD MoS2 memristors, a current compliance‐regulated Ag filament mechanism is revealed. The filament ruptures spontaneously during volatile switching, while subsequent growth proceeds vertically through the MoS2 layers and then laterally along the van der Waals gaps during nonvolatile switching.
Yuan Fa   +19 more
wiley   +1 more source

Home - About - Disclaimer - Privacy