Results 61 to 70 of about 521,562 (282)
Advanced Engineering Materials, Volume 27, Issue 6, March 2025.The stability criteria affecting the formation of high‐entropy alloys, particularly focusing in supersaturated solid solutions produced by mechanical alloying, are analyzed. Criteria based on Hume–Rothery rules are distinguished from those derived from thermodynamic relations. The formers are generally applicable to mechanically alloyed samples.
Javier S. Blázquez +5 more
wiley +1 more source
Odontoid remodeling with occipital condyle stabilization in patients with metastatic C2 involvement
Journal of Craniovertebral Junction and SpineThe occipitocervical junction (OCJ) is a complex anatomical region crucial for protecting the lower brain stem, upper spinal cord, and lower cranial nerves. Instability in this area can lead to severe outcomes such as chronic pain, neurological deficits,
Mehmet Yigit Akgun +7 more
doaj +1 more source
Harnessing Fungal Biowelding for Constructing Mycelium‐Engineered Materials
Advanced Engineering Materials, EarlyView.Mycelium‐bound composites (MBCs) offer low‐carbon alternatives for construction, yet interfacial bonding remains a critical challenge. This review examines fungal biowelding as a biocompatible adhesive, elucidating mycelium‐mediated interfacial mechanisms and their role in material assembly. Strategies to optimize biowelding are discussed, highlighting
Xue Brenda Bai +2 more
wiley +1 more source
INFLUENCE OF THE STIFFNESS AND FRICTIONAL CHARACTERISTICS ON THE SHANK TORQUE OF SCREWS IN BOLTED JOINTS [PDF]
, 2018 This work aims at determining the influence of tribological and stiffness characteristics of a bolted joint on the residual shank torque of the screw.
Cavalli, Omar +6 more
core
Advanced Engineering Materials, EarlyView.This article demonstrates the successful qualification of a copper–tungsten composite for laser powder bed fusion. The resulting components exhibited high density, high thermal conductivity, and reduced thermal expansion. Heat sinks with complex geometries were successfully manufactured, clearly showcasing the material's potential for additive ...
Simon Rauh +6 more
wiley +1 more source
Finite element analysis of a novel anatomical plate in posterolateral plateau fractures
Frontiers in SurgeryObjectiveThis study aims to analyze the biomechanical characteristics of posterolateral plateau fractures fixed by a novel anatomical plate using finite element analysis.MethodsA three-dimensional digital model of the full length of right tibiofibula was
Zhen Jian +5 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.This study examines how several molten high‐silicon electrical steels interact with both conventional and recycled MgO–C refractories. For this, various immersion experiments are conducted. In addition to infiltration, a number of mechanisms are identified and explained that control the corrosion of the refractory material.
Lukas Neubert +7 more
wiley +1 more source
Explanation of the discrepancy between the measured and atomistically calculated yield stresses in body-centered cubic metals [PDF]
, 2006 We propose a mesoscopic model that explains the factor of two to three discrepancy between experimentally measured yield stresses of BCC metals at low temperatures and typical Peierls stresses determined by atomistic simulations of isolated screw ...
Aono Y +4 more
core +3 more sources
Effect of Oxygen Content on Surface and Subsurface Integrity During Turning of Ti–6Al–4V
Advanced Engineering Materials, EarlyView.This study examines how oxygen content in the ambient atmosphere affects the surface and subsurface properties of Ti–6Al–4V during turning. Results show that oxygen does not influence surface roughness. However, machining in an extremely high vacuum‐adequate atmosphere increases surface hardness by up to 7.8% and induces compressive residual stresses ...
Benjamin Bergmann +3 more
wiley +1 more source
BioengineeringJones fractures are Zone 2 fractures of the fifth metatarsal. Biomechanical comparisons of fixation strategies for Jones fractures remain limited by the lack of standardized, head-to-head evaluations across major fixation methods.
Cheng-Min Shih +5 more
doaj +1 more source