Results 21 to 30 of about 95,125 (344)
Gas leakage and distribution characteristics of methyl bromide and sulfuryl fluoride during fumigations in a pilot flour mill [PDF]
, 2012 The half-loss time (HLT) is used as an indicator to quantify gas leakage rates during methyl bromide (MB) and sulfuryl fluoride (SF) fumigations. Comparisons of HLTs between three MB and three SF fumigations were quantified in the Hal Ross pilot flour ...
Watcharapol Chayaprasert +23 more
core +6 more sources
Geofluids, 2017 An effective sealing system is crucial for CO2-EOR storage, and these sealing systems are typically composed of the caprocks and faults that surround a reservoir. Therefore, the sealing effectiveness of a caprock-fault system must be evaluated at various
Bing Bai +4 more
doaj +1 more source
Journal of Rock Mechanics and Geotechnical Engineering, 2023 During the operation of compressed air storage energy system, the rapid change of air pressure in a cavern will cause drastic changes in air density and permeability coefficient of sealing layer.
Shikang Qin, Caichu Xia, Shuwei Zhou
doaj +1 more source
Journal of Veterinary Medical Science, 2003 Spotted seals (Phoca largha) and related crossbreeds maintained at Kamogawa Sea World breed seasonally from the end of January to middle of March. For contraception in these animals, the effect of a single administration of a contraceptive synthetic luteal hormone for dogs, proligestone (PRG), was investigated.
Etsuko, Katsumata +2 more
openaire +3 more sources
Cost effectiveness of crack treatment methods: A field study
Journal of Traffic and Transportation Engineering (English ed. Online), 2019 In the United States, more than 94% highways are paved with asphalt materials and placing crack sealant materials has been a common pavement maintenance for decades.
Mithil Mazumder +3 more
doaj +1 more source
Numerical Investigation of the Effect of Radial Lip Seal Geometry on Sealing Performance [PDF]
IOP Conference Series: Materials Science and Engineering, 2018 Sealing elements are often needed in industry and especially in machine design. With the change and development of machine technology from day to day, sealing elements show continuous development and change in parallel with these developments. Many factors influence the performance of the sealing elements such as shaft surface roughness, radial force ...
Tok, Görkem +2 more
openaire +2 more sources
Special Cement Slurries for Strengthening Salt Rock Mass
Energies, 2022 Every year, the number of exploited mine workings necessary to seal the exploited mines increases in the world. As a result of experiments, technologies are developed that allow slurry to be pumped to fill free rock spaces or to liquidate rock mass ...
Stanisław Stryczek +2 more
doaj +1 more source
Nellix endovascular aortic sealing endoprosthesis late explantation for concomitant type I endoleak and stent frames proximal caudal migration [PDF]
, 2019 Endovascular aneurysm sealing (EVAS) using the Nellix™ System was introduced in clinical practice with the aim of reducing the incidence of complications such as migration, endoleaks, and reinterventions after conventional endovascular aneurysm repair ...
Di Girolamo, A. +4 more
core +1 more source
Optimizing induction sealing for milk bottles at different conveyor speeds [PDF]
E3S Web of ConferencesOptimal sealing helps reduce milk spoilage amid rising temperatures caused by climate change. One potential solution is the use of alufo plastic on the bottle mouth with an induction sealing machine.
Anwar Saiful +9 more
doaj +1 more source
Impact of Purge Injection on Rim Seal Performance
Applied SciencesOne of the most critical challenges in gas turbine design is preventing the ingestion of hot mainstream gases into the disk space between the stator and rotor disks.
Matteo Caciolli +4 more
doaj +1 more source