Results 81 to 90 of about 1,535 (289)
Adaptive Foam 3D Printing of Ultralight and Multifunctional Materials
Advanced Engineering Materials, EarlyView.Adaptive foam 3D printing, enabled by expandable microspheres, imparts cellular structures to thermoplastic and thermosetting polymers, manufactured through a variety of processes including fused filament fabrication, direct ink writing, digital light processing, and inkjet printing.
Nariman Rajabifar, Amir Ameli
wiley +1 more source
Self‐Cleaning Sensor Surfaces for Long‐Term Environmental Monitoring
Advanced Engineering Materials, EarlyView.Long‐term use of unattended outdoor sensors without soiling or biofouling is achieved through generation of a micro‐ and nanorough cuvette surface by combing hydrophobic nanoparticles with fluorinated polymers, crosslinked and surface‐attached through CHic chemistry. The coating demonstrates self‐cleaning behavior and prolonged outdoor stability, which
Sanam Kumari Rajak +4 more
wiley +1 more source
Minoan and Mycenaean elements in the iconography of the Pylos sealings
, 1985 Tamvaki Angela. Minoan and Mycenaean elements in the iconography of the Pylos sealings. In: Bulletin de correspondance hellénique. Supplément 11, 1985. pp.
Angela Tamvaki, Tamvaki, Angela
core +1 more source
Advanced Engineering Materials, EarlyView.CT‐based finite element simulations combined with in situ X‐ray computed tomography are used to analyze insert pull‐out in nickel‐coated polymer foams. Despite variations in material parameters, deformation consistently concentrates within a narrow annular region around the insert.
Yannik Bautz +4 more
wiley +1 more source
Fabrication Routes for Ionic Conducting Fiber Strain Sensors
Advanced Engineering Materials, EarlyView.Ionic conducting fiber strain sensors (ICFSs) offer compliant, textile‐integrable sensing. Thus far, the commercialization of ICFSs has been constrained by fiber fabrication routes. This review provides a fabrication‐centric analysis of ICFSs correlating processing strategies with material properties and scalability.
Leo John Kershaw +3 more
wiley +1 more source
A tile model of circuit topology for self-entangled biopolymers. [PDF]
Sci Rep, 2023 Flapan E, Mashaghi A, Wong H.
europepmc +1 more source
Rapidly Solidified High‐Strength Invar 36 Prepared by Planar‐Flow Melt Spinning
Advanced Engineering Materials, EarlyView.The Invar 36 alloy was rapidly solidified using the planar‐flow melt‐spinning technique. Ribbon samples with thicknesses ranging from 20 to 160 mm were produced. As the grain size of the ribbon decreased to sub‐micron levels, the hardness increased by more than 2 times.
Bekir Akgül, Mehmet Kul
wiley +1 more source
Mobility to, from and within Neopalatial Crete: The Evidence from the Sealings [PDF]
, 2018 This paper focuses on the occurrence of sealings impressed by the same seal faces or by very similar seal faces at different archaeological sites in LM I. Sealings are small clay lumps impressed one or more times with one or more seal faces, and at times
Barbara Montecchi, Montecchi, Barbara
core +1 more source
Frontiers in Environmental ArchaeologyOne of the milestones in the trajectory of economic and social change that spurred increasing societal complexity, and urbanization was the commodification of natural resources, such as plants, animals, and their derived products.
Karolina Joka
doaj +1 more source
The new coronavirus and its influence on the achievement of minimum skills in Stomatology students
Revista Científica Estudiantil 2 de Diciembre, 2021 Introduction: the educational teaching process of the Stomatology career in the 2019-2020 and 2020-2021 academic years was affected by the presence of SARS-CoV-2 and the biosecurity measures taken to prevent infection.
Idanny Chávez Taset +5 more
doaj