Results 41 to 50 of about 153,018 (297)
Advanced Engineering Materials, Volume 28, Issue 11, 3 June 2026.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
Imaging with Diffractive Axicons Rapidly Milled on Sapphire by Femtosecond Laser Ablation
Engineering Proceedings, 2023 We show that single-pulse burst fabrication will produce a flatter and smoother profile of axicons milled on sapphire compared to pulse overlapped fabrication which results in a damaged and much rougher surface.
Daniel Smith +5 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.High‐frequency (HF) welding of steel is limited by oxide inclusions that degrade weld quality. This study demonstrates, for the first time, the integration of a nonthermal Ar/H2 dielectric barrier discharge (DBD) plasma jet into HF welding. Local plasma treatment provides effective shielding and in‐situ oxide reduction, resulting in markedly fewer and ...
Viktor Udachin +4 more
wiley +1 more source
Micromachines, 2023 Ultra-short 230 fs laser pulses of a 515 nm wavelength were tightly focused onto 700 nm focal spots and utilised in opening ∼0.4–1 μm holes in alumina Al2O3 etch masks with a 20–50 nm thickness.
Jovan Maksimovic +8 more
doaj +1 more source
Robot-sensor synchronization for real-time seamtracking in robotic laser welding [PDF]
, 2005 The accuracy requirements of laser welding put high demands on the manipulator that is used. To use industrial six-axis robots for manipulating the laser welding optics, sensors measuring the seam trajectory close to the focal spot are required to meet ...
Aarts, R.G.K.M. +3 more
core +3 more sources
Development of a research methodology and analysis of the stress state of a parting under the joint and downward mining of coal seams [PDF]
, 2018 Purpose. The investigation of the stress-strain state (SSS) of a parting under the joint and downward mining of coal seams. Methods. The studies have been carried out on the basis of a computational experiment by means of the finite elements method ...
Barabash, M, Kovalevska, I, Snihur, V
core +1 more source
Influence of an Argon/Silane Atmosphere on the Temperature of a Thermal Plasma
Advanced Engineering Materials, EarlyView.The influence of a silane‐doped argon atmosphere on the chemical composition and temperature of a thermal nontransferring argon plasma is investigated using optical emission spectroscopy. As a result of the high amount of free electrons resulting from the stepwise ionization and dissociation of the silane molecule, even a silane addition of 0.01 vol ...
Lena Kreie +4 more
wiley +1 more source
Mechanism conversion process and timeliness of N2-ECBM [PDF]
, 2018 Purpose. Based on the technology by which methane drainage is strengthened under gas injection, to examine the process of gas injection and the mechanism of action. Methods.
Chen, L, Wang, L, Yang, H, Yang, T
core +1 more source
Advanced Engineering Materials, EarlyView.This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff +9 more
wiley +1 more source
Sensors, 2020 Multiple wire twisted steel strands are commonly used to hoist elevators, concrete structures, etc. Due to frequent and long-time usage, the steel strands are subjected to corrosion, overloads, and aging, making strands may fail unexpectedly.
Edison Z.Y. Hou +3 more
doaj +1 more source