Results 51 to 60 of about 4,961 (263)

Functional Method of Designing Self-Compacting Concrete [PDF]

Materials, 2021
The article presents a new functional method of designing self-compacting concrete (SCC). The assumptions of the functional method of designing self-compacting concrete were based on the double coating assumption (i.e., it was assumed that the grains of coarse aggregate were coated with a layer of cement mortar, whereas the grains of sand with cement ...
openaire   +2 more sources

Electrochemical Behavior of Flame‐Sprayed Sc‐Doped AlCoCrFeMo High‐Entropy Alloy Coatings in 3.5% Sodium Chloride Solution

Advanced Engineering Materials, EarlyView.
Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar, Akash Vyas, Mohammad Aatif Qazi, Nashit Jalal, Maria Ophelia Jarligo, Mostafa Yakout, Jing Liu, André McDonald   +7 more
wiley   +1 more source

Molecular Dynamics Studies of Shape Memory Polymers: From Bead–Spring Models to Atomistic Simulations

Advanced Engineering Materials, EarlyView.
Coarse‐grained (left) and atomistic (right) models of the shape memory polymer ESTANE ETE 75DT3 are shown schematically. The two representations bridge molecular detail and mesoscopic description. Both models capture shape memory behavior, linking segmental mobility and conformational relaxation of anisotropic chains to macroscopic recovery, and ...
Fathollah Varnik
wiley   +1 more source

THE EFFECT OF CURING TYPES ON STRENGTH OF SELF COMPACTING CONCRETE [PDF]

Fayoum University Journal of Engineering, 2018
The main purpose of this study is to investigate the effect of using three types of curing (water, painting, and room air) and three different types of water and cement on the strength of self-compacting concrete.
Ahmed Abd El-azim, Hany El-Ghazaly, Manar Abdul Hady   +2 more
doaj   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Properties of Normal and High-Strength self-Compacting Fibrous Concrete in Fresh and Hardened state

Journal of Engineering and Sustainable Development, 2014
This paper studies the properties of normal and high strength self-compacting concrete in the fresh and hardened states, six self-compacting with normal and high strength concrete mixes were prepared with different percentages of fibers(0, 0.4%, and 0.
Mohammed Mosleh Salman, Ihsan Al-Shaarbaf, Jassim Muhsin Aliewi   +2 more
doaj  

A Practical Noise2Noise Denoising Pipeline for High‐Throughput Raman Spectroscopy

Advanced Engineering Materials, EarlyView.
A lightweight and reproducible denoising pipeline for high‐throughput Raman spectroscopy is introduced, based on a 1D convolutional autoencoder trained with a Noise2Noise strategy. Using only repeated short‐exposure acquisitions, the method suppresses stochastic noise without reference spectra, enabling reliable spectral reconstruction while preserving
David Martin‐Calle, Cesar Alvarez‐Llamas, Vincent Motto‐Ros, Christophe Dujardin, Jérémie Margueritat, David Rodney   +5 more
wiley   +1 more source

Active Corrosion Protection of Sintered AA7075 Aluminum Alloy via Mn Powder Addition

Advanced Engineering Materials, EarlyView.
AA7075 containing Mn‐rich particles is fabricated via spark plasma sintering using AA7075 and Mn powders. Corrosion resistance is evaluated through dip‐and‐dry tests using 0.1 M NaCl (pH 6.0), and mass loss decreases with increasing Mn addition. Mn‐rich particles function as a source of Mn ions, and formation of Mn‐accumulation films on Cu‐containing ...
Ko Ebina, Masashi Nishimoto, Izumi Muto
wiley   +1 more source

Extrusion‐Based Additive Manufacturing of Advanced Ceramics: Strengthening Mechanisms and Process Optimization Review

Advanced Engineering Materials, EarlyView.
This review comprehensively evaluates extrusion‐based additive manufacturing for advanced ceramics, detailing feedstock options and key process parameters. By critically addressing defect mechanisms like porosity and cracking, the work highlights optimization strategies through machine learning and advanced postprocessing.
Meisam Bakhtiari, Mohammad Hadi Sheikh‐Ansari, Avinash Borgaonkar, Mehran Dadkhah, Abdollah Saboori   +4 more
wiley   +1 more source

Semantic Modeling in Materials Science and Engineering With Platform MaterialDigital Core Ontology 3.0

Advanced Engineering Materials, EarlyView.
The community‐driven Platform MaterialDigital Core Ontology (PMDco) 3.0 is introduced as a Basic Formal Ontology‐aligned semantic backbone for the processing–structure–properties paradigm in Materials Science and Engineering. Modular engineering, automated releases, and validation workflows are highlighted and key semantic patterns for materials ...
Markus Schilling, Philipp von Hartrott, Jörg Waitelonis, Thomas Hanke, Henk Birkholz, Hossein Beygi Nasrabadi, Khashayar Razghandi, Kamilla Zaripova, Felix Thonagel, Fabian Neuhaus, Martin Glauer, Lars Vogt, Harald Sack, Lutz Mädler, Bernd Bayerlein, Chris Eberl   +15 more
wiley   +1 more source