Results 21 to 30 of about 80,277 (234)
Morphological Study of Surface Magnetic Minerals, Case Study of North Banjarmasin Settlement Areas
Jurnal Fisika FluxWe have conducted research to identify the morphology of magnetic minerals from the land in the Banjarmasin regional settlement area. We used scanning electron microscopy and energy dispersive X-ray spectroscopy (SEM EDS) on the soil sample to look at ...
Sudarningsih Sudarningsih +3 more
doaj +1 more source
Results in OpticsIn the present work, one-step, mass-scale productive solid state reaction method has been employed for the preparation of gadolinium (Gd) doped ZnO (GZOx: x = 0, 2, 4, 6, 8 wt%) nanostructures.
Rajesh Kumar +3 more
doaj +1 more source
Structural, Morphological and Magnetic Properties of Zn0.5Mg0.5Fe2O4 as Anticorrosion Pigment
International Journal of Electrochemical Science, 2015 Glycine-assisted combustion route used for elaboration spinel Zn0.5Mg0.5Fe2O4. X-ray diffraction (XRD), scanning electron micrographs (SEM), energy dispersive spectrometry (EDS) and infrared (IR) spectroscopy, attributive this ferrite.
N.M. Deraz, Omar H. Abd-Elkader
doaj +1 more source
Monte Carlo strategy for SEM-EDS micro-nanoanalysis of geopolymer composites
Composites Part C: Open Access, 2021 The development, optimization and application of new geopolymer composite materials must necessarily go through a precise and accurate physico-chemical and mineralogical characterization down to the micro and nanoscale.
Daniele Moro +2 more
doaj +1 more source
SCANNING ELECTRON MICROSCOPY: AN ESSENTIAL TOOL IN THE INVESTIGATION OF CEMENT FOR OIL WELLS
Química NovaOil well cementing plays a critical role in ensuring zonal isolation, structural integrity, and long-term well safety. Due to exposure to high pressures, temperatures, and chemically aggressive environments, understanding the microstructural behavior of ...
Rafael A. Ventura +3 more
doaj +1 more source
Use of SEM and EDS analysis in the investigation of Al-Si-Cu piston alloy cast porosity [PDF]
Metalurgija, 2009 Porosity formation was detected in the casting thinnest section in the proximity of the as cast surface and near the wall centerline. In order to investigate the cause of the porosity formation light microscopy was used to define as cast structure. After
D. Kakaš +4 more
doaj
Journal of Analytical Science and Technology, 2019 Background With the application of the scanning transmission electron microscopy (STEM) detector, transmitted electron images similar to transmission electron microscopy (TEM) can be obtained from scanning electron microscopy (SEM), which is referred to ...
Yong-Eun Kwon +4 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley +1 more source
Morphological analysis of the seeds of three pseudocereals by using light microscopy and ESEM-EDS
European Journal of Histochemistry, 2020 The seed morphology of three Pseudocereal Grains (PSCg), i.e. quinoa (Chenopodium quinoa Willd, Chenopodiaceae), buckwheat (Fagopyrum esculentum Moench, Polygonaceae) and amaranth (Amaranthus caudatus L., Amaranthaceae) was studied by light microscopy ...
Paolino Ninfali +4 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo +3 more
wiley +1 more source