Results 201 to 210 of about 92,239 (294)

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source

Sensory Outcomes and Neurotization Techniques Following Mastectomies: A Comprehensive Systematic Review. [PDF]

Cancers (Basel)
Zhou B, Cipurko D, Dejenie R, Zietowski M, Wong D, Hanson SE.   +5 more
europepmc   +1 more source

Prediction of Surface Topography Parameters in Direct Laser Interference Patterning of Stainless Steel Using Infrared Monitoring and Convolutional Neural Networks

Advanced Engineering Materials, EarlyView.
This study presents an infrared monitoring approach for direct laser interference patterning (DLIP) combined with a convolutional neural network (CNN). Thermal emission data captured during structuring are used to predict surface topography parameters.
Lukas Olawsky, Marcelo Sallese, Leander Kläber, Clemens Kuhn, Keming Du, Andrés Fabián Lasagni   +5 more
wiley   +1 more source

Preoperative Diagnostic Factors Associated With Early MCID Achievement in BCTQ Outcomes Following Carpal Tunnel Release. [PDF]

J Hand Surg Glob Online
Iglesias B, Weinberg J, Gonzalez C, Gopakumar A, Afolabi-Brown K, Dan X, Ma Y, Fowler J.   +7 more
europepmc   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Pain in Alzheimer's Disease: Disrupted Multilevel Integration of Nociception, Affective Processing and Clinical Expression Across Clinical and Preclinical Evidence. [PDF]

Life (Basel)
Stanciu GD, Costachescu I, Gogu RM, Tamba BI.   +3 more
europepmc   +1 more source

Reduction of Oxide Inclusions During the High‐Frequency Welding of Steel via a Nonthermal Ar/H2 Plasma Jet

Advanced Engineering Materials, EarlyView.
High‐frequency (HF) welding of steel is limited by oxide inclusions that degrade weld quality. This study demonstrates, for the first time, the integration of a nonthermal Ar/H2 dielectric barrier discharge (DBD) plasma jet into HF welding. Local plasma treatment provides effective shielding and in‐situ oxide reduction, resulting in markedly fewer and ...
Viktor Udachin, Lienhard Wegewitz, René Gustus, Henning Wiche, Wolfgang Maus‐Friedrichs   +4 more
wiley   +1 more source

Handbook of Establishing and Maintaining Oxygen‐Free Atmospheres

Advanced Engineering Materials, EarlyView.
This study presents a practical framework for creating oxygen‐free atmospheres at ambient pressure using silane‐doped inert gases. The results show that ultra‐low oxygen levels and strongly reduced water content can be achieved through controlled silane dosing, drying systems, and sensor monitoring.
Sascha Jan Zimmermann, René Gustus, Lienhard Wegewitz, Wolfgang Maus‐Friedrichs   +3 more
wiley   +1 more source

Development of a Sensory Evaluation Method for Polyphenols via Analysis of Chemical Structure and Organoleptic Properties: A Pilot Study. [PDF]

Foods
Nakamura H, Ogata M, Shimizu T, Fujii Y, Aso K, Tagata C, Calabrese V, Osakabe N.   +7 more
europepmc   +1 more source

Additive Gaussian Process Regression for Predictive Design of High‐Performance, Printable Silicones

Advanced Engineering Materials, EarlyView.
A chemistry‐aware design framework for tuning printable polydimethylsiloxane (PDMS) for vat photopolymerization (VPP) is developed using additive Gaussian process (GP) modeling. Polymer network mechanics informs variable groupings, feasible formulation constraints, and interaction variables.
Roxana Carbonell, Martha Leach, Hongtao Song, Carolyn Seepersad   +3 more
wiley   +1 more source