Results 171 to 180 of about 998,789 (338)

Bulk Tea Shoot Detection and Profiling Method for Tea Plucking Machines Using an RGB-D Camera. [PDF]

Sensors (Basel)
Cai Y, Li X, Yi W, Liu G.
europepmc   +1 more source

Determination of Optimum Cutter Shape for Peeling Altari Radish [PDF]

Journal of Biosystems Engineering, 2003
openaire   +1 more source

Thermoelectric Modules Incorporating MgAgSb and Mg3(Sb,Bi)2 Synthesized Using a Melting Method

Advanced Engineering Materials, EarlyView.
A scalable synthesis method for a thermoelectric material of MgAgSb is established. A thermoelectric power module of MgAgSb/Mg3(Sb,Bi)2 is fabricated, showing the conversion efficiency of 7.4% at ΔT = 315 K. The performance is comparable to conventional Bi2Te3 modules when they are operated with an air‐cooled heat exchanger.
Kazuo Nagase, Hironori Ohshima, Kunihiro Kihou, Haruno Kunioka, Ushin Anazawa, Ryosuke Sakagami, Yosuke Goto, Masayuki Murata, Chul‐Ho Lee   +8 more
wiley   +1 more source

A novel ultrasonic intraocular lens (IOL) cutting tip and IOL holding forcep. [PDF]

Indian J Ophthalmol
Dholakia N, Pirdankar OH, Shah S.
europepmc   +1 more source

Four‐Point Bending Tests at High Temperatures on Commercial MgO‐C Refractory Bricks with and Without Recyclate Considering Different Carbon Contents

Advanced Engineering Materials, EarlyView.
Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm, Lukas Knöchel, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +5 more
wiley   +1 more source

Pore Evolution Mechanism in Granite during Ultrasonic Vibration-Assisted Penetration by a Disc Cutter. [PDF]

ACS Omega
Ma X, Han J.
europepmc   +1 more source

Distribution of Electrical Resistivity in Single Carbon Fiber Filaments and Its Correlation With Tensile Modulus

Advanced Engineering Materials, EarlyView.
A statistical framework is applied to quantify the distribution of electrical resistivity among individual filaments of two commercially available carbon fiber types. Correlations between filament resistivity, tensile modulus, and diameter are examined and complemented by TEM analysis to provide new insight into filament‐level variability relevant for ...
Nils Wieja, Daniel Sebastian Wolz, Philip Johannes Steinbild, Markus Löffler, Darius Pohl, Jan Wolf, Anja Winkler, Thomas Behnisch, Bernd Rellinghaus, Maik Gude   +9 more
wiley   +1 more source

Simulation study of rock-breaking performance of TBM cone-shape cutterhead under different tunneling parameters in spiral tunnel. [PDF]

Sci Prog
Lin L, Liu K, Ji Z, Qi M, Wang J, Xiao J, Xia Y, Yang M.   +7 more
europepmc   +1 more source

Population of Nonmetallic Inclusions in Liquid High‐Silicon Electrical Steel in Contact With MgO–C Refractories Based on Recyclates and Environmentally Friendly Binders

Advanced Engineering Materials, EarlyView.
The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert, Matheus Roberto Bellé, Florian Kerber, Dinesh Kumar Gunasekar, Hans‐Jörn Weddige, Christos G. Aneziris, Olena Volkova   +6 more
wiley   +1 more source

A high-precision segmentation method based on UNet for disc cutter holder of shield machine. [PDF]

Sci Rep
Peng D, Zhu G, Xie Z.
europepmc   +1 more source