Results 151 to 160 of about 37,909 (300)
Materials & DesignThe dynamic behavior of flat-nosed Ti-6Al-4V (TC4) alloy projectiles penetrating Q235 steel targets under three velocities (800 m/s, 983 m/s, and 1167 m/s) was studied experimentally and numerically, emphasizing the evolution of adiabatic shear bands of ...
Yue Zhou +6 more
doaj +1 more source
Advanced Functional Materials, EarlyView.We use scanning nitrogen vacancy magnetometry to directly image the weak in‐plane magnetic moments in mixed phase BiFeO3 at the nanoscale and quantify the local magnetic moments to be 18.8±2.0 μB/nm2 in the rhombohedral‐like phase and 1.5±0.6 μB/nm2 in the well‐known non‐magnetic tetragonal‐like phase.
Lei Wang +14 more
wiley +1 more source
Effect of Shear Bands Induced by Asymmetric Rolling on Microstructure and Texture Evolution of Non-Oriented 3.3% Si Steel. [PDF]
Materials (Basel), 2020 Fang Z +6 more
europepmc +1 more source
Glissile Interphase Boundaries Enable Collective Phase Switching in Epitaxial Polar Oxides
Advanced Functional Materials, EarlyView.A triple point is identified in the phase diagram of low‐symmetry epitaxial BiFeO3 thin film along with an extended regime of phase competition associated with a flattened energy landscape. The electromechanical response is shown to be governed by correlated interphase‐boundary motion, including scale‐free avalanche dynamics characteristic of systems ...
Mohammad Moein Seyfouri +11 more
wiley +1 more source
Advanced Functional Materials, EarlyView.This article details the development of an artery‐on‐chip platform for in vitro arterial disease modeling and therapeutic discovery. It describes the fabrication of a fibrin biomaterial scaffold seeded with iPSC‐derived smooth muscle and endothelial cells, mimicking native artery properties. Two genetic disease models showcase the platform's ability to
Danielle Yarbrough +10 more
wiley +1 more source
Advanced Functional Materials, EarlyView.A high‐Zn2+‐transference hydrogel electrolyte of ex‐PDADAM is developed via anion exchange at quaternary ammonium sites, achieving high Zn2+ transference number (0.86), ionic conductivity (8.10 mS cm−1), and toughness (51.25 MJ m−3). Symmetric cells are operated stably for over 2000 h, while flexible pouch cells retain 90.9% capacity after 300 cycles ...
Jung Woo Hong +8 more
wiley +1 more source
Enhanced Mechanical and Corrosion Performance by Forming Micro Shear Bands in Cold Forged Mg-Gd-Y-Zr Alloy. [PDF]
Materials (Basel), 2020 Yang Z, Liu C, Gao Y, Guo X, Wan Y.
europepmc +1 more source
Advanced Functional Materials, EarlyView.Co‐delivery of electrosprayed EDOT and oxidant enables bulk oxidative polymerization during layer‐by‐layer fabrication, creating stable, highly conductive 3D PEDOT structures. This Atomized Oxidative Polymerization (AOP) overcomes the surface deposition‐only and matrix‐limited conductivity of conventional Vapor Phase Polymerization (VPP) and PEDOT:PSS ...
Tazdik Patwary Plateau +2 more
wiley +1 more source
Review of Thermally Activated Twisted Coiled Polymer Actuators: A Materials Science Perspective
Advanced Functional Materials, EarlyView.Thermally activated twisted and coiled polymer actuators (TCPAs) combine lightweight design, large deformation, and scalable fabrication for soft robotic and wearable applications. This review connects polymer structure, processing history, helix geometry, and thermomechanical characterization to actuator performance, highlighting current challenges in
Nadja Schenk +3 more
wiley +1 more source
Double‐Interpenetrating Composite Bioink for Multi‐Component 3D Bioprinting and Biofabrication
Advanced Functional Materials, EarlyView.Marine‐polysaccharides‐derived double interpenetrating network hydrogel‐based bioink, combining the attributes of physical and ionic crosslinking, enables room‐temperature bioprinting of mechanically defined structures that can be handled and are cytocompatible.
Fabian Tribukait‐Riemenschneider +1 more
wiley +1 more source