Results 21 to 30 of about 10,152 (262)
Advanced Engineering Materials, EarlyView.A numerical–experimental framework is developed for characterizing multi‐matrix fiber‐reinforced polymers (MM‐FRPs) combining epoxy and polyurethane matrices. Harmonic bending tests are integrated with finite element model updating (FEMU) to simultaneously identify elastic and viscoelastic material parameters.
Rodrigo M. Dartora +4 more
wiley +1 more source
Shear Lag Effects in Angles Welded at Both Legs
Advances in Civil Engineering, 2019 The shear lag phenomenon is known to reduce the tensile capacity of tension members. There are various parameters affecting shear lag that have not been considered before. In addition, previous studies have been conducted mainly on single steel sections.
Mohammad Abedin +3 more
doaj +1 more source
The Baltic Journal of Road and Bridge Engineering, 2023 The composite box girder with corrugated web and steel bottom plate (CW-SBS) is a kind of improved steel-concrete structures. The design of CW-SBS box girders needs the accurate method to calculate the working response and accordion effect in ...
Ya-Nan Gan, Zi-Chen Zhang, Gen-Hui Wang
doaj +1 more source
Creep‐Induced Microstructural Evolution in an A2‐B2 Superalloy
Advanced Engineering Materials, EarlyView.A 27.3Ta‐27.3Mo‐27.3Ti‐8Cr‐10Al (at.%) refractory high‐entropy alloy with precipitation‐strengthened A2‐B2 microstructure was studied by creep tests at 1030°C, which demonstrate a transition in deformation mechanisms in the range of 100–150 MPa applied stress. This is associated with changes in dislocation–precipitate interactions. Relevant deformation
Liu Yang +10 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This work studies the anisotropic behavior of circular notched tensile specimens of Ni‐base superalloy single crystals during high‐temperature tensile creep along [001], [110], and [111]. Correlative scale‐bridging imaging of specimens reveals early rupture along [110] because 1) plastic deformation proceeds faster at notch center; 2) more (brittle ...
Leonardo Agudo Jácome +6 more
wiley +1 more source
BuildingsThe study presents an analysis of steel-Ultra-High Performance Concrete (UHPC) composite girders. Five composite girder specimens were designed and tested.
Hua Luo +5 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees +6 more
wiley +1 more source
Study on the Deflection Calculation of a Steel Truss Web–Concrete Composite Beam Under Pre-Stress
BuildingsThe aim of this study is to establish an accurate calculation method for the deflection caused by the effect of pre-stress in a steel truss web–concrete composite girder bridge based on the energy variational principle, considering the influence of shear
Chunmei Ni +3 more
doaj +1 more source
Control of Polarization and Polar Helicity in BiFeO3 by Epitaxial Strain and Interfacial Chemistry
Advanced Functional Materials, EarlyView.In BiFeO3 thin films, the interplay of interfacial chemistry, electrostatics, and epitaxial strain is engineered to stabilize homohelicity in polarization textures at the domain scale. The synergistic use of a Bi2O2‐terminated Aurivillius buffer layer and a highly anisotropic compressive epitaxial strain offers new routes to control the polar‐texture ...
Elzbieta Gradauskaite +5 more
wiley +1 more source
Applied SciencesThis paper presents an analytical method based on the shear flow distribution law to study the shear lag effect of thin-walled single- and double-cell box girders.
Yuan Shi +3 more
doaj +1 more source