Results 351 to 360 of about 3,769,575 (399)
Some of the next articles are maybe not open access.
Estimation of Shear Strength of Structural Shear Walls
Journal of Structural Engineering, 2010An analysis method for predicting the shear strength and behavior of structural shear walls under both monotonic and cyclic loading is presented in this paper. The proposed analysis method is based on the softened truss model theory and utilizes a newly proposed cracking angle of the concrete strut.
Wael Kassem, Ahmed Elsheikh
openaire +2 more sources
Shear strength of orthodontic bonding agents
The European Journal of Orthodontics, 1988The aim of this study was to compare the in vitro bond strength to enamel measured in shear of the light-activated bonding agent Heliosit-Orthodontic with the shear bond strength of the two-paste bonding resin Concise and the ‘no-mix’ bonding resin Right-On.
E. Dresner +3 more
openaire +3 more sources
Shear strength of the human lumbar spine
Clinical Biomechanics, 2012Shear loading is recognised as a risk factor for lower back pain. Previous studies of shear loading have either not addressed the influence of age, bone mineral density, axial height loss due to creep or were performed on animal specimens.Intact human lumbar motion segments (L2-3) were tested in shear using a modified materials testing machine, while ...
Nicholas E. Bishop +8 more
openaire +3 more sources
2001
Shear loads in an aircraft fuselage will occur as a result of bending and torsion. Yield values under shear are necessary during the design phase since the material should not deform plastically below the limit load. The Metal Volume Fraction (MVF) method for shear yield strength prediction of Glare laminates was investigated.
openaire +2 more sources
Shear loads in an aircraft fuselage will occur as a result of bending and torsion. Yield values under shear are necessary during the design phase since the material should not deform plastically below the limit load. The Metal Volume Fraction (MVF) method for shear yield strength prediction of Glare laminates was investigated.
openaire +2 more sources
Shear Strength of FRP Reinforced Concrete Members with Stirrups
, 2015The mechanisms of shear transfer in fiber-reinforced polymer (FRP) reinforced concrete members with shear reinforcement are discussed, and it is explained how these were used to derive the shear design provisions of the Canadian standard for design and ...
A. Razaqpur, S. Spadea
semanticscholar +1 more source
On the compressibility and shear strength of natural clays
, 1990The compressibility and strength characteristics of reconstituted clays are used as a basic frame of reference for interpreting the corresponding characteristics of natural sedimentary clays.
J. Burland
semanticscholar +1 more source
, 2015
An experimental investigation was conducted to study the mechanical properties and shear strength of full-scale beams constructed with recycled concrete aggregate (RCA). This study included two RCA mixtures and one conventional concrete (CC) mixture. The
M. Arezoumandi +3 more
semanticscholar +1 more source
An experimental investigation was conducted to study the mechanical properties and shear strength of full-scale beams constructed with recycled concrete aggregate (RCA). This study included two RCA mixtures and one conventional concrete (CC) mixture. The
M. Arezoumandi +3 more
semanticscholar +1 more source
Improved nonlinear Burgers shear creep model based on the time-dependent shear strength for rock
Environmental Earth Sciences, 2020Hang Lin +3 more
semanticscholar +1 more source
, 2015
A laboratory research program was undertaken to study the large-strain shear strength characteristics of fine-grained soils under low effective normal stresses (∼3–7 kPa).
T. EidHisham +3 more
semanticscholar +1 more source
A laboratory research program was undertaken to study the large-strain shear strength characteristics of fine-grained soils under low effective normal stresses (∼3–7 kPa).
T. EidHisham +3 more
semanticscholar +1 more source