Results 51 to 60 of about 117,331 (259)
Advanced Engineering Materials, EarlyView.Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth +6 more
wiley +1 more source
Experimental Study on the Shear Strength of Cement-Sand-Gravel Material
Advances in Materials Science and Engineering, 2018 An experimental study on the shear strength development of cement-sand-gravel (CSG) material was carried out using triaxial compression tests. The effects of the cementing agent content, aggregate content, and gradation on the shear strength of CSG ...
Jie Yang +5 more
doaj +1 more source
Performance of Stud Clusters in Precast Bridge Decks
The Baltic Journal of Road and Bridge Engineering, 2014 A new design approach to clustered stud shear connection in composite bridges with precast decks is required to accommodate highly concentrated shear force in small area. Shear connection of the prefabricated slab consists of stud connectors, mortar in a
Chang-Su Shim +2 more
doaj +1 more source
Advances in Materials Science and Engineering, 2021 The bonding behaviors of the plate-concrete interface of a composite structure consisting of a concrete block in the middle and two cement plates at both sides play a key role in its overall mechanical performance.
Lifeng Zhang +5 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Nickel‐based alloys are widely used in high‐temperature applications due to their excellent mechanical strength and oxidation resistance. However, properties such as high‐temperature strength and pronounced work‐hardening make them difficult to machine.
Soheil Rooein +2 more
wiley +1 more source
Effect of Laser Deoxidation on Adhesive‐Bonded Aluminum in an Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.This study investigates laser ablation of aluminum under oxygen‐free conditions. The goal is to produce oxide‐free substrates that enable improved adhesive bonding with epoxy. Optimized laser parameters (90% overlap, 300 µJ) combined with oxide‐free substrates result in the highest tensile strength of the adhesive bond.
Sandra Gerland +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm +5 more
wiley +1 more source
Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics
Advanced Engineering Materials, EarlyView.Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost +4 more
wiley +1 more source
Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V
Advanced Engineering Materials, EarlyView.Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study develops sustainable MgO–C refractories using recycled materials and eco‐friendly fructose–tannin binders. The enhanced performance of citric acid as a cross‐linker and functional additives on mechanical and thermomechanical properties was examined. Characterization included strength tests, immersion trials, and microstructural and inclusion
Dinesh K. Gunasekar +7 more
wiley +1 more source