Results 41 to 50 of about 2,684,777 (125)

Analysis of hybrid Nd:Yag laser-MAG arc welding processes. [PDF]

open access: yes, 2011
In the hybrid laser-arc welding process, a laser beam and an electric arc are coupled in order to combine the advantages of both processes: high welding speed, low thermal load and high depth penetration thanks to the laser; less demanding on joint ...
F. Coste   +9 more
core   +1 more source

INITIAL ARC IGNITION CONTROL IN GAS-SHIELDED WELDING

open access: yesAdvanced Engineering Research, 2011
The control method of the initial arc ignition in the gas-shielded welding is offered. It is based on the short-circuit current limitation after heating the wire stick-out with the metal passing current to the plastic state for the time of the wire ...
Evgeny N. Varukha   +2 more
doaj  

Box-Behnken Based Analysis of Slag Consumption in Submerged Arc Welding of High Strength Low Alloy Steel [PDF]

open access: yesArchives of Metallurgy and Materials
The present research work involves the placing of a small quantity of molten steel into the gap among the components to be connected, subsequently positioning them together during solidification.
Krishan Kant Sharma   +6 more
doaj   +1 more source

INITIAL ARC IGNITION CONTROL IN GAS-SHIELDED WELDING

open access: yesВестник Донского государственного технического университета, 2018
The control method of the initial arc ignition in the gas-shielded welding is offered. It is based on the short-circuit current limitation after heating the wire stick-out with the metal passing current to the plastic state for the time of the wire ...
Evgeny N. Varukha   +2 more
doaj  

Measuring the process efficiency of controlled gas metal arc welding processes [PDF]

open access: yes, 2011
The thermal or process efficiency in gas metal arc welding (GMAW) is a crucial input to numerical models of the process and requires the use of an accurate welding calorimeter.
Colegrove, Paul A.   +11 more
core   +1 more source

The optimization of welding regime parameters at shielded metal arc welding (SMAW) by mathematical modeling

open access: yesMetalurgija, 2016
The realized researches followed the determining of mathematical models that allow the optimization of the welding process in order to obtain welded joints with certain values of the mechanical characteristics.
V. Petrescu, G. Paraschiv, D. Dobrotă
doaj  

Study of welding productivity for MIL A 46100steel weldments produced using GMAW and SMAW

open access: yesRevista Facultad de Ingeniería Universidad de Antioquia, 2012
A study was conducted to measure welding productivity for MIL A46100 specification steel joints welded following five different welding procedures (WPS) which used gas metal arc welding (GMAW), in mechanized mode, and shielded metal arc welding (SMAW ...
David Mazuera Robledo   +2 more
doaj   +1 more source

Physicomathematical modeling of the formation features of fillet welds of bridge metal structures under submerged-arc welding

open access: yesAdvanced Engineering Research, 2020
Introduction. The weld formation under the submerged-arc welding of bridge metal structures is investigated. The work objective is to study possibilities to increase the welding performance during the arc welding of fillet seams.
A. A. Mosin   +2 more
doaj   +1 more source

Optimization of shielded metal arc welding process parameters on weld bead geometry using Jaya algorithm and Firefly algorithm

open access: yesAdvances in Mechanical Engineering
The foremost aspect in welding is to improve the mechanical and microstructural properties in the weldment. The properties depend upon the weld bead characteristics. This is in turn depend upon the welding process.
Pushp Kumar Baghel
doaj   +1 more source

The Effect of Niobium Addition on the Operational and Metallurgical Behavior of Fe-Cr-C Hardfacing Deposited by Shielded Metal Arc Welding

open access: yesJournal of Manufacturing and Materials Processing
Hardfacing is commonly used in parts recovery and in obtaining surfaces with improved properties. Within this field, it is important to analyze the effect of alloying elements on the properties of the deposited layers.
Jaime Perez   +4 more
doaj   +1 more source

Home - About - Disclaimer - Privacy