Results 201 to 210 of about 128,623 (299)

Recycling of NiTi Shape Memory Alloys: Fundamental and Technological Aspects of a Vacuum Induction Melting Processing Route

Advanced Engineering Materials, EarlyView.
The present study investigates recycling of NiTi shape memory alloys via vacuum induction melting. An ingot was synthesized from elemental Ni and Ti and subjected to three subsequent remelting cycles. Remelting increases process durations and impurity levels and adversely affects microstructures and functional properties.
Sakia Sophia Noorzayee, Son Tung Mai, Sarath Menon, Braulio Gadiel Sánchez Ortega, Ralf Drautz, Alexander Kauffmann, Gunther Eggeler, Jan Frenzel   +7 more
wiley   +1 more source

Comparative evaluation of several models for forecasting hourly electricity use in a steel plant. [PDF]

Sci Rep
Gu F, Zhao Y.
europepmc   +1 more source

A New Approach to Detection of Systematic Errors in Secondary Substation Monitoring Equipment Based on Short Term Load Forecasting. [PDF]

Sensors (Basel), 2016
Moriano J, Rodríguez FJ, Martín P, Jiménez JA, Vuksanovic B.   +4 more
europepmc   +1 more source

Bioinspired Shape‐Memory Hook Fasteners With Programmable Interlocking and Silent Release

Advanced Engineering Materials, EarlyView.
Bioinspired hook fasteners made from epoxy shape‐memory polymers are shown to switch between strong, secure attachment and gentle, silent release when heated. By combining programmable geometry and material response, these adaptive fasteners outperform commercial systems in strength and noise control, enabling new solutions for robotics, medical ...
Maria I. Vallejo Ciro, Manuel J. Carvajal Loaiza, Rahaf Homssi, Vanessa Restrepo   +3 more
wiley   +1 more source

Impact of accurate load forecasting on electricity market stability in Japan using classical time-series and deep-learning methods. [PDF]

Sci Rep
Rabie D, Moradi M, Xuan W, Farzaneh H.
europepmc   +1 more source

Evaluation of Plasticity and Creep Parameters From Tensile Stress–Strain Data for a Range of Strain Rates

Advanced Engineering Materials, EarlyView.
This plot compares experimental tensile stress–strain curves (with 4 different strain rates) and corresponding modelled curves (obtained using the optimised sets of Voce and Miller–Norton parameter values shown). The inferred M‐N values, characterizing the creep, are very similar to those obtained via conventional creep testing.
S. Ooi, R. P. Thompson, T. W. Clyne
wiley   +1 more source

Electricity consumption prediction using an advanced spatial-temporal deep learning framework. [PDF]

Sci Rep
A Palan V, N S.
europepmc   +1 more source

Molecular Dynamics Studies of Shape Memory Polymers: From Bead–Spring Models to Atomistic Simulations

Advanced Engineering Materials, EarlyView.
Coarse‐grained (left) and atomistic (right) models of the shape memory polymer ESTANE ETE 75DT3 are shown schematically. The two representations bridge molecular detail and mesoscopic description. Both models capture shape memory behavior, linking segmental mobility and conformational relaxation of anisotropic chains to macroscopic recovery, and ...
Fathollah Varnik
wiley   +1 more source

MTMF-Grid: A multi-task multi-modal fusion model for operational forecasting and decision support in power grids. [PDF]

PLoS One
Zhang D, Shen B, Li P, Wang P, Sheng Y, Bing Y.   +5 more
europepmc   +1 more source

Nondestructive Testing of Welded Composite Metal Foams

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography (CT) is used to evaluate welded steel–steel composite metal foam (CMF) joints of two density classes. It reports variation in postweld spatial void distribution and correlates it to weld‐induced changes, mechanical performance, and failure within welded CMF panels.
Chinmaya Prerana Inguva, Aman Kaushik, Afsaneh Rabiei   +2 more
wiley   +1 more source