Results 101 to 110 of about 26,531 (262)

An Auction Algorithm for Shortest Paths [PDF]

SIAM Journal on Optimization, 1991
Summary: A new and simple algorithm for finding shortest paths in a directed graph is proposed. In the single origin-single destination case, the algorithm maintains a single path starting at the origin, which is extended or contracted by a single node at each iteration.
openaire   +2 more sources

Precipitation Simulations of the O‐Phase in Ti2AlNb Alloys Processed by Laser Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
Simulated and experimental evolution of the O‐phase volume fraction during postprocessing of a Ti‐21Al‐25Nb (at.%) alloy processed by laser powder bed fusion. With results of sensitivity to input parameters from a thorough and quantified analysis, the interfacial energy matrix/precipitate is the most relevant input parameter for the simulation of the O‐
Silvana Tumminello, Joachim Gussone, Suzana G. Fries, Marcus Rackel, Andreas Stark, Norbert Schell, Jan Haubrich, Guillermo Requena   +7 more
wiley   +1 more source

Inverse Identification of Energy‐Dependent Laser Absorptivity in NiTi Laser Powder‐Bed Fusion via Calibrated Melt Pool Simulation

Advanced Engineering Materials, EarlyView.
A combined experimental–computational framework identifies energy‐dependent laser absorptivity for NiTi in laser powder‐bed fusion, applicable to conduction and transition modes. Single‐track experiments and thermofluid smoothed particle hydrodynamics simulations are coupled through inverse analysis of melt pool geometry.
Mohamadreza Afrasiabi, Hadi Moutablaleh, Ignatius A. Setiawan, Mehrshad Mehrpouya   +3 more
wiley   +1 more source

Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading

Advanced Engineering Materials, EarlyView.
This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev, Noah‐Lean Roschlaub, Anne Jung   +2 more
wiley   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Defect Evolution and Mechanical Performance of Fused Filament Fabrication‐Manufactured 17‐4PH Stainless Steel Revealed by X‐Ray Computed Tomography

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography reveals how process‐induced defects evolve from green to sintered states in Fused Filament Fabrication (FFF)‐manufactured 17‐4PH stainless steel. Internal porosity, weakest cross‐sections, and fracture locations show strong correlation with tensile performance, demonstrating the potential of computed tomography (CT)‐based ...
György Ledniczky, Márk Sárközi, Ibolya Zsoldos, Zoltán Weltsch   +3 more
wiley   +1 more source

Precedence‐Constrained Shortest Path

Networks
ABSTRACTWe propose a variant of the shortest path problem where the order in which vertices occur in the path is subject to precedence constraints. Precedence constraints are defined in terms of vertex pairs which indicate that a vertex is the predecessor of a vertex .
Christina Büsing, Dennis John, Corinna Mathwieser   +2 more
openaire   +2 more sources

External and Internal Cracking Caused by Heat Treatment in Laser Powder Bed Fusion‐Fabricated Inconel 738LC Components

Advanced Engineering Materials, EarlyView.
Manufacturing problems such as heat treatment‐induced cracking hinder the widespread application of the laser powder bed fusion (LPBF) process to superalloys. In this study, cracks in the LPBF components of Inconel 738LC superalloy are characterized after heat treatment at various temperature ranges, revealing two distinct cracking behaviors.
Kosuke Kuwabara, Masahiro Kusano, Ayako Ikeda, Toshio Osada, Makoto Watanabe   +4 more
wiley   +1 more source

Transportation network reduction [PDF]

Transport Problems, 2015
Network reduction problem is formulated as follows: We are given a transportation network T, a set of important origin – destination relations R and a number q greater than 1.
Stanislav PALÚCH, Štefan PEŠKO, Tomáš MAJER, Jan ČERNÝ   +3 more
doaj  

Extrusion‐Based Additive Manufacturing of Advanced Ceramics: Strengthening Mechanisms and Process Optimization Review

Advanced Engineering Materials, EarlyView.
This review comprehensively evaluates extrusion‐based additive manufacturing for advanced ceramics, detailing feedstock options and key process parameters. By critically addressing defect mechanisms like porosity and cracking, the work highlights optimization strategies through machine learning and advanced postprocessing.
Meisam Bakhtiari, Mohammad Hadi Sheikh‐Ansari, Avinash Borgaonkar, Mehran Dadkhah, Abdollah Saboori   +4 more
wiley   +1 more source