Results 51 to 60 of about 368,698 (305)
Effect of Sample Reconstitution Methods on the Behaviors of Granular Materials under Shearing [PDF]
, 2018 The effect of sample reconstitution methods on the behavior of sand under shearing is investigated by using the first commercially available Variable Direction Dynamic Cyclic Simple Shear System. Three sample reconstitution methods are used in this study,
Li, Y, Roberts, G, Yang, Y, Yu, H
core +1 more source
A Workflow to Accelerate Microstructure‐Sensitive Fatigue Life Predictions
Advanced Engineering Materials, EarlyView.This study introduces a workflow to accelerate predictions of microstructure‐sensitive fatigue life. Results from frameworks with varying levels of simplification are benchmarked against published reference results. The analysis reveals a trade‐off between accuracy and model complexity, offering researchers a practical guide for selecting the optimal ...
Luca Loiodice +2 more
wiley +1 more source
Evaluation of asphalt pavement layer bonding stress
Journal of Civil Engineering and Management, 2015 This study is to evaluate the bonding shear stress between asphalt pavement layered structures with emulsion and cutback asphalt as tack coat materials.
Jia-Chong Du
doaj +1 more source
Advances in Materials Science and Engineering, 2021 The shear key in the reinforced concrete open-web sandwich plate (RCOSP) is a block joint that connects with the top chord and the bottom chord. In order to understand the failure mode of the shear key and verify the accuracy of the current algorithm, a ...
Hongna Lu +4 more
doaj +1 more source
Zein‐Based Adhesives: Sustainable Extraction and Application in Bioadhesive Technologies
Advanced Engineering Materials, EarlyView.Zein is extracted from corn gluten meal using a simple and scalable process with high yield (~90%). The resulting protein is applied in bioadhesives modified with Ca2+ and Fe3+ ions, exhibiting substrate‐dependent adhesion. The findings demonstrate competitive bonding performance and highlight the role of ionic interactions in tuning adhesion ...
Paula Bertolino Sanvezzo +3 more
wiley +1 more source
Torsion Test vs. Other Methods to Obtain the Shear Strength of Elastic-Plastic Adhesives
Applied Sciences, 2022 Nowadays adhesive joints are more and more used; therefore, a precise and reliable shear strength measurement of these joints is necessary to design and predict a final components’ performance.
Monica Ferraris +5 more
doaj +1 more source
The non-monotonic shear-thinning flow of two strongly cohesive concentrated suspensions
, 2014 The behaviour in simple shear of two concentrated and strongly cohesive mineral suspensions showing highly non-monotonic flow curves is described. Two rheometric test modes were employed, controlled stress and controlled shear-rate.
Buscall, Richard +6 more
core +1 more source
Advanced Engineering Materials, EarlyView.A numerical–experimental framework is developed for characterizing multi‐matrix fiber‐reinforced polymers (MM‐FRPs) combining epoxy and polyurethane matrices. Harmonic bending tests are integrated with finite element model updating (FEMU) to simultaneously identify elastic and viscoelastic material parameters.
Rodrigo M. Dartora +4 more
wiley +1 more source
SHEAR STRENGTH OF REINFORCED CONCRETE T-BEAMS WITHOUT STIRRUPS [PDF]
Journal of Engineering Science and Technology, 2016 This paper presents the test results of experimental study on shear strength of reinforced concrete beams without stirrups. The test variables in this study were type of beam cross section and ratio of longitudinal reinforcement.
RENDY THAMRIN +4 more
doaj
A methodology to measure the interface shear strength by means of the fiber push-in test [PDF]
, 2012 A methodology is presented to measure the fiber/matrix interface shear strength in composites. The strategy is based on performing a fiber push-in test at the central fiber of highly-packed fiber clusters with hexagonal symmetry which are often found ...
González Martínez, Carlos Daniel +3 more
core +2 more sources