Results 181 to 190 of about 263,020 (218)
Some of the next articles are maybe not open access.
Forces in Single Point and Two Point Incremental Forming
Advanced Materials Research, 2005Forces have been measured in Two Point Incremental Forming and Single Point Incremental Forming of Sheet Metal. It is necessary to know the magnitude of these forces when trying to determine if the equipment available is capable of Forming Sheet Metal by either one of the two foregoing processes.
J. Jeswiet +2 more
openaire +1 more source
Modularity Design of Single Point Incremental Forming Machine
Applied Mechanics and Materials, 2023Currently, the research on the application of Single point incremental forming technology (SPIF) in Vietnam is limited. Therefore, the study of technology and equipment for the fabrication of SPIF machine and research on the ability of deformation of the formed material sheet is necessary and should be urgently carried out.
Thanh Nam Nguyen +4 more
openaire +1 more source
Single point incremental forming of polyamide/30 wt% short glass fiber composite
Journal of Thermoplastic Composite Materials, 2022The experimental study of single point incremental forming (SPIF) of a thermoplastic matrix composite (TMC) was presented in this research. The TMC’s matrix was built of polyamide (PA) 6.6, and the reinforcement was 30 wt percent short glass fiber (GF ...
Sareh Bagheri, A. Kami, M. Shakouri
semanticscholar +1 more source
Formability of polycarbonate sheets in single-point incremental forming
The International Journal of Advanced Manufacturing Technology, 2019The paper investigates the influence of tool diameter, sheet thickness, and geometry of the workpiece during single-point incremental forming (SPIF) of polycarbonate sheets. An experimental campaign was conducted and involved varying and fixed slope angle tests. The process was performed at room temperature.
Durante, Massimo +2 more
openaire +3 more sources
Single Point Incremental Forming of Large Sheet Metal Components
Volume 2A: Advanced Manufacturing, 2019Abstract The production of complex, large-scale cladding parts made of metal in small quantities for a wide range of applications in architecture, power generation, shipbuilding, but also rail vehicle construction, mobile work machines and, last but not least, automotive sector is a major challenge in terms of principled ...
Schieck, Frank +3 more
openaire +1 more source
Twist revisited: Twist phenomena in single point incremental forming
CIRP Annals, 2010Abstract Twist phenomena in incrementally formed parts have been observed both in the domain of single and two point incremental forming. In the reported experiments the resulting twist direction typically corresponds to the toolpath direction and can be explained by the monotonous tangential force component exerted on the workpiece when using ...
Duflou, Joost +5 more
openaire +2 more sources
Prediction of forming forces in single point incremental forming
Journal of Manufacturing Processes, 2017Incremental sheet forming (ISF) is a cost effective die-less forming process for low volume production. Achieving good accuracy using this process is a challenging task. Bending between clamped boundary and component opening, tool deflection, sheet spring-back and rigid body displacements are the major reasons for geometric inaccuracy in components ...
Ankush Bansal +3 more
openaire +2 more sources
Single Point Incremental Forming Using Flexible Die
2016Incremental sheet forming is an innovative process having ability to fulfill demands for customized sheet metal parts without using costly dies unlike traditional forming processes. However, shape deviation of formed parts is one of the drawbacks which need technological developments to use ISF on shop floor.
Deepesh Panjwani +5 more
openaire +1 more source
Process Parameters Optimization in Single Point Incremental Forming
Journal of The Institution of Engineers (India): Series C, 2015This work aims to optimize the formability and surface roughness of parts formed by the single-point incremental forming process for an Aluminium-6063 alloy. The tests are based on Taguchi’s L18 orthogonal array selected on the basis of DOF. The tests have been carried out on vertical machining center (DMC70V); using CAD/CAM software (SolidWorks V5 ...
Vishal Gulati +3 more
openaire +1 more source
Mechanics of fracture in single point incremental forming
Journal of Materials Processing Technology, 2012Abstract Single point incremental forming (SPIF) is a sheet metal forming technique which has gained considerable interest in the research community due to its enhanced formability, greater process flexibility and reduced forming forces. However, a significant impediment in the industrial adoption of this process is the accurate prediction of ...
Rajiv Malhotra +3 more
openaire +1 more source