Results 171 to 180 of about 4,824 (239)

High-temperature sintered 3D-printed alumina as mechanically robust supports for MOF catalysis.

Mater Adv
Schöfbeck F, Eder T, Zeng W, Brouczek D, Schwentenwein M, Benseghir Y, Reithofer MR, Chin JM.   +7 more
europepmc   +1 more source

Optimizing sintering air volume for enhanced lean gas recovery and environmental performance. [PDF]

Sci Rep
Guo X, Ji J, Gao Y, Wu X, Guo Y, Wang W, Wen M, Wu X, Zhang Z.   +8 more
europepmc   +1 more source

Degradation Mechanisms in PEM Water Electrolysis: Diagnosis and Impact

Advanced Materials Technologies, EarlyView.
This review provides an analysis of degradation mechanisms in proton electrolyte membrane water electrolyzers (PEMWE), focusing on all key components. It discusses diagnostic and measurement techniques for evaluating degradation, less‐studied mechanisms, and an expert survey.
Annik Bernhardt, Katja Lange, Robert Göckeritz, Erik Grunwald, Angelika Hähnel, Alexander Müller, Volker Naumann, Sistan Rasuli, Wolfram Münchgesang, Bruno G. Pollet, Kerstin Witte‐Bodnar, Klemens Ilse   +11 more
wiley   +1 more source

Microbial diversity at remediated former gold and copper mines and the metal tolerance of indigenous microbial strains. [PDF]

Appl Environ Microbiol
Velianyk V, Palusak M, Nguyen NHA, Riha J, Sevcu A, Cernik M, Hlavackova V.   +6 more
europepmc   +1 more source

Molecular Inks for the Development of Complex 3D In‐Mold Electronics

Advanced Materials Technologies, EarlyView.
Molecular inks (MINKs) enable the fabrication of thermoformed 3D circuits by decoupling the forming and metallization steps. Following thermoforming, intense pulsed‑light or thermal processing converts the patterned MINKs into complex 3D conductive tracks with improved stretchability and electrical performance, advancing low‑cost, high‑performance in ...
Mehal P. Kushalkar, Hiroshi Fukutani, Olga Mozenson, Jianying Ouyang, Liliana Gaburici, Bhavana Deore, Dayna Bennett, Chantal Paquet, Paul Trudeau, Loleï Khoun, Nicolas Milliken, Olivier Ferrand, Julie Ferrigno, Xiangyang Liu, Arnold J. Kell   +14 more
wiley   +1 more source

Uncertainty-Quantified Primary Particle Size Prediction in Li-Rich NCM Materials via Machine Learning and Chemistry-Aware Imputation. [PDF]

Adv Sci (Weinh)
Madika B, Kang C, Shim J, Park T, Moon JH, Cho E, Hong S.   +6 more
europepmc   +1 more source

3D Printing of Stretchable, Compressible and Conductive Porous Polyurethane for Soft Robotics

Advanced Materials Technologies, EarlyView.
A 3D‐printable porous dopamine‐polyurethane acrylate elastomer results in conductive, stretchable, and compressible structures that can be metallized in situ through catechol‐mediated silver reduction. The resulting material function as both compliant soft robot with a and strain sensors without complex assemblies, enabling fully 3D‐printed soft ...
Ouriel Bliah, Konstantin Sakharov, Pooi See Lee, Shlomo Magdassi   +3 more
wiley   +1 more source

Impact of social rewarding in dynamic shop floor environments. [PDF]

Sci Rep
Sait U, Frego M, De Angeli A, Peer A.
europepmc   +1 more source

Additive Manufacturing of Ni‐Based Thermoelectric Materials for Waste Heat Recovery

Advanced Materials Technologies, EarlyView.
Thermoelectric generators convert waste heat into electricity but are constrained by conventional fabrication. Here, laser powder bed fusion enables direct printing of customised n‐type Cu60Ni40 and p‐type Ni90Cr10 legs. The assembled module achieves 0.8% efficiency at ΔT = 419 K, demonstrating scalable additive manufacturing of eco‐friendly, design ...
Karolin Amstein, Aayush Dobhal, Heiko Reith, Ran He, Julia Kristin Hufenbach, Kornelius Nielsch, Pingjun Ying   +6 more
wiley   +1 more source