Results 11 to 20 of about 17,982,164 (331)
Influence of Biomass Absorptivity on the Process of Sinter Charge Pelletisation
Applied Sciences, 2020 Capillary water absorption of materials is a very important factor in the process of pre-treatment of fine-grained materials. Materials that are in a moisturized state capable of forming a firm, compact pellet are, thanks to this particular physical ...
Martina Džupková +4 more
doaj +1 more source
Metals, 2022 The fuel segregation distribution sintering process, with a high fuel dosage in upper layer and a low fuel dosage in bottom layer of the sintering bed, was studied to handle uneven heat distribution problems in the conventional iron ore sintering process.
Qiangjian Gao +5 more
doaj +1 more source
Energies, 2020 During development of substitute anode materials suitable for solid oxide fuel cell (SOFC), understanding of sintering mechanisms and effects is significant for synthesized porous structures and performance.
Chaoyu Liang +6 more
doaj +1 more source
Analysis of printing parameters for metal additive manufactured parts through Direct Ink Writing process [PDF]
, 2020 Direct Ink Writing is an Additive Manufacturing process in which a metal ink is continuously extruded to built-up a green metal part. Therefore, a debinding and sintering process is required to obtain the final metal part. This thermal process produces a
Bonada Bo, Jordi +6 more
core +2 more sources
A phenomenological analysis of sintering kinetics from the viewpoint of activated volume [PDF]
Science of Sintering, 2005 The sintering kinetics of real systems has been viewed as a process of transport of activated volume. Activated volume is a parameter that can be used to describe mass transport during the sintering process.
Nikolić M.V. +2 more
doaj +1 more source
Crystals, 2022 Lead-free piezoelectric 0.92(K0.445Na0.5Li0.05)NbO3-0.08BaZrO3 (KNLN-BZ) ceramics were prepared via conventional sintering. Single-step, 2-step and 3-step temperature-controlled conditions were designed.
Yan Tang +8 more
doaj +1 more source
The Evolution of Microstructure and Magneto-structural Properties of Heat Treated NI-MN-SN-IN Heusler Alloys Sintered by Vacuum Hot Pressing [PDF]
Archives of Metallurgy and Materials, 2019 In this work, vacuum hot pressed Ni-Mn-Sn-In Heusler alloys with different concentration of In (0, 2 and 4 at.%), were investigated. The magneto-structural behaviour and microstructure dependencies on chemical composition and on heat treatment were ...
W. Maziarz +7 more
doaj +1 more source
Study on the Influence of the New Type of Powder Metallurgy Ti-Al-Nb Alloy Hot Press Sintering Process on the Microstructure [PDF]
E3S Web of Conferences, 2021 Based on the hot-pressing sintering process, the kinetics of hot-pressing sintering crystal grain growth and the hot-pressing sintering densification kinetics, the mixing ratio of the raw material powder and the hot-pressing sintering system are designed.
Fang Shuang +3 more
doaj +1 more source
Investigation of the Oven Process in Indirect Metal Laser Sintering [PDF]
, 2004 This paper deals with the optimization of Indirect Metal Laser Sintering. Different experimental analyses have proven that the oven process is highly responsible for the part distortion.
Seefried, M., Zaeh, M. F.
core +1 more source
Optimal allocation of limonite in sintering process
工程科学学报, 2022 Improvements in ore blending could be realized by an optimal match of iron ores, sinters, and fuel conditions. To further increase iron grade and reduce the cost of ore blending, in view of the actual raw material and fuel conditions of the 500 m2 large ...
Guo-cheng ZHANG +5 more
doaj +1 more source