Results 11 to 20 of about 46,299 (310)
Low-sintering-temperature garnet oxides by conformal sintering-aid coating [PDF]
SSRN Electronic Journal, 2021 Abstract Garnet-type solid electrolytes have attracted an extensive attention for high-energy solid-state lithium batteries. However, the high processing temperature up to 1200°C with high cost limits the large-scale production. Here, we report a simple approach to reduce the sintering temperature by a conformal coating of nanoscale amorphous ...
Shaojie Chen +13 more
openaire +3 more sources
The Effects of Sintering Temperature and Addition of TiH2 on the Sintering Process of Cu [PDF]
Materials, 2019 In this study, effects of sintering temperature and TiH2 on the sintering process of Cu are investigated. During sintering, the oxide in Cu decomposes and generates oxygen, which can become trapped in the material forming closed pores. Therefore, this results in low sintered density.
Hao, Huali +6 more
openaire +2 more sources
Coalescence behavior of Cu nanoparticles during sintering: Based on atomic scale to macro scale
Journal of Materials Research and Technology, 2023 Due to the excellent electrothermal properties, outstanding resistance to electromigration and cost-effectiveness, Cu nanoparticles are considered as a promising bonding material for high-power device.
Jiaxin Liu +4 more
doaj +1 more source
Low Temperature Sintering of PZT
Journal of Physics: Conference Series, 2014 This paper describes the fabrication and characterization of lead zirconate titanate (PZT) films fired in a liquid-phase sintering process at 900 °C in air. In detail the manufacturing of piezoelectric multilayers with internal pure silver (Tm = 961 °C) electrodes are reported. The feasibility of ten sintering aids in two different volume fractions was
Medesi, A. +4 more
openaire +4 more sources
Parameter optimization for sintering of La0.6Sr0.4Co0.2Fe0.8O3-6 (LSCF6428) perovskite-structured ceramics by Taguchi method [PDF]
Science of Sintering, 2016 The influence of sintering temperature, sintering time and heating rate on the shrinkage rate, sintered density and porosity of La0.6Sr0.4Co0.2Fe0.8O3-ó (LSCF6428) perovskite-structured ceramics has been analyzed and the optimum sintering ...
Hashim Siti Salwa +2 more
doaj +1 more source
Study HTHP Sintered WC/Co Hardmetal [PDF]
Materials Research, 2016 WC/Co is widely used as cutting tools, because has a unique combination of high strength, hardness, toughness, and moderate stiffness, especially with fine grained WC and finely distributed cobalt.
Meysam Mashhadikarimi +4 more
doaj +1 more source
Journal of Asian Ceramic Societies, 2023 Diopside-anorthite glass-ceramics were prepared by direct sintering with extracted titanium slag (ETS), coal fly ash (CFA) and quartz sand (SA), the effect of sintering temperature (1120–1180°C) and the SiO2/Al2O3 ratio (1.85–2.63) on the phase ...
Tao Chen +3 more
doaj +1 more source
Design and fault diagnosis of DCS sintering furnace's temperature control system for edge computing.
PLoS ONE, 2021 Under the background of modern industrial processing and production, the sintering furnace's temperature control system is researched to achieve intelligent smelting and reduce energy consumption.
Na Qu, Wen You
doaj +1 more source
Characterization of mechanically milled and spark plasma sintered Al2124-CNT nanocomposites [PDF]
Science of Sintering, 2015 In the present work, ball milling and spark plasma sintering were used to develop Al2124-CNT nanocomposites. The effect of milling time on the grain size and lattice strain of the ball milled Al2124 alloy powder and the effect of sintering time ...
Saheb N.
doaj +1 more source
Effects of sintering temperature on W-Mo-Cu alloy prepared by large current electric field sintering
Cailiao gongcheng, 2019 The W-Mo-Cu alloy was rapidly prepared by a large current electric field sintering method at 875-1000℃. Effect of sintering temperature on microstructure, hardness and electrical conductivity was investigated. Based on the dimensional change during alloy
LIU Yan-fang +3 more
doaj +1 more source