Results 151 to 160 of about 109,365 (297)

Mitigating Creep Anisotropy and Enhancing Performance in Additively Manufactured Ni‐Based Superalloys: A Review

Advanced Engineering Materials, EarlyView.
Additive manufacturing introduces pronounced microstructural and crystallographic anisotropy in Ni‐based superalloys, resulting in orientation‐dependent creep deformation and damage. This review identifies the key microstructural origins of creep anisotropy, examines their influence on dominant deformation mechanisms, and highlights processing ...
Chandan Kumar, Shobhit Pratap Singh, Gaurav Mohanty, Praveen Kumar   +3 more
wiley   +1 more source

Electrodeposition in Structural Lattices of Variable Architectures

Advanced Engineering Materials, EarlyView.
Electrodeposition enables geometry‐sensitive, autonomous void filling while simultaneously tuning chemical and mechanical properties. The development of approaches that can autonomously fill and heal material voids and yield composites with tailorable properties is increasingly relevant in engineering.
Yeong‐Man Kwon, Jingwen Zhang, Guido Musso, Alessandro F. Rotta Loria   +3 more
wiley   +1 more source

The properties and acceptability of fresh cheese produced using the mixture probiotic culture

Mljekarstvo, 2002
Investigation and production of dairy food with probiotic cultures isincreasing due to its health and nutritive benefits. In this paper the probiotic fresh cheese was produced from skim milk samples with 0,1% fat (A) and 1,0% fat (B).
Rajka Božanić, Ljubica Tratnik, Ida Drgalić   +2 more
doaj  

Microstructure‑Dependent Phase Transformations Under High‑Pressure Laser Heating in Additively Manufactured AlCrFe2Ni2

Advanced Engineering Materials, EarlyView.
Additively manufactured AlCrFe2Ni2 with contrasting BCC/B2‐dominant and lamellar FCC + BCC/B2 microstructures exhibits the same pressure‐induced BCC/B2 → HCP transformation. Under laser heating at high pressure, HCP is destabilized, and a cubic BCC/B2 + FCC assemblage is recovered, while the lower‐scan‐speed microstructure transforms at a lower ...
Raimundas Sereika, Hunter Kantelis, Yogesh K. Vohra, Shengbiao Zhang, Wuxian Yang, Wen Chen   +5 more
wiley   +1 more source

Thermal Cycle–Microstructure–Property Relationships in Rail Steel Heat‐Affected Zone Simulated by Gleeble

Advanced Engineering Materials, EarlyView.
Microstructural evolution of premium rail steel during flash butt welding (FBW), comparing physically simulated heat‐affected zones with actual weld regions. Thermal cycles induce phase transformations and microstructural heterogeneity that influence weld quality and mechanical performance. These findings provide insights into optimizing FBW parameters
Emmanoelle Cintra da Cunha Araújo, João Marcos da Silva Nunes, Marcelly Cristiny Nunes de Carvalho, Alex Rojas, Cristie Luis Kugelmeier, Cristhian Ricardo Loayza Loayza, João Carlos Ferreira, Maria Veronica Goncalves Rodrigues, Rute Sayuri Kano, Isaac Araújo Furtado, Jacyara Dalylla da Silva Nunes, Jhonatan Peres de Sousa, Marcos Natan da Silva Lima, Eden Santos Silva, Gedeon Silva Reis, Samuel Filgueiras Rodrigues   +15 more
wiley   +1 more source

Functional and Fertility Outcomes of Two Milk-Based Extenders for Short-Term Storage of Ram Semen at 15°C. [PDF]

Reprod Domest Anim
Neila-Montero M, Iniesta-Cuerda M, Hernández-Serrano J, Díaz-Hernández E, Vidal-Garcia C, Laborda-Gomariz JÁ, Serrallé M, Gallego R, García-García Ó, Garde JJ, Soler AJ.   +10 more
europepmc   +1 more source

Digital Light Processing of Thermoplastic Poly(methyl methacrylate) Photoresin Combined With Solvent Vapor Smoothing

Advanced Engineering Materials, EarlyView.
A thermoplastic PMMA‐based photoresin enables high‐resolution DLP printing followed by solvent‐vapor smoothing. The treatment reduces staircase‐induced surface roughness from 2.33 µm to 129 nm and increases visible‐light transmittance from approximately 30% to 80%, providing a route toward transparent PMMA components for rapid prototyping and non ...
Rozhin Heydarpour, Yuanyuan Li, Sebastian Kluck, Afnan Qazzazie‐Hauser, Bastian E. Rapp, Frederik Kotz‐Helmer   +5 more
wiley   +1 more source

SKIM: A fast sketching strategy integrated with model's dynamic-feedback for large-scale single-cell transcriptomic analysis. [PDF]

PLoS Comput Biol
Bai J, Zhou F, Tan C, Gao Y, He Y, Huang X, Wang Y.   +6 more
europepmc   +1 more source

Influence of Particle Shape and Size in Copper‐Based Low‐Temperature Metallization Paste for Solar Cells

Advanced Engineering Materials, EarlyView.
Particle morphology controls the balance between printability and electrical connectivity in low‐temperature AgCu/Ag metallization pastes. Flake‐shaped AgCu particles form extended low‐resistance contacts, whereas spherical particles favor processability at high metal loading. Fine Ag particles further tune void filling and conductive‐network formation
O. Mhirsi, M. N. Wengenmeyr, J. Bartsch, B. E. Rapp   +3 more
wiley   +1 more source

Liquid-phase milk turbidimetry enables rapid phenotyping of secreted protease activity in <i>Pseudomonas aeruginosa</i> at less than one cent per sample. [PDF]

Microbiol Spectr
Enríquez-Ríos KD, Pineda-Licona JC, García-Reyes S.   +2 more
europepmc   +1 more source