Results 71 to 80 of about 437,510 (295)
Advanced Energy and Sustainability Research, Volume 6, Issue 10, October 2025.Hydrogen is an energy carrier, produced from renewable and nonrenewable resources. It can be stored in a variety of materials and transported to distant locations. This article reviews progress in hydrogen technology by looking at environmental and economic impact, cost analysis, and policy support at government level as way forward for bringing it to ...
Xuexue Pan +5 more
wiley +1 more source
Effect of Repeated Loads on the Low Temperature Fracture Behavior of Notched and Welded Plates [PDF]
, 1967 The influence of repeated loadings on the susceptibility of weldments to fracture in a brittle manner is studied for an ABS-Class C steel. The test members have consisted primarily of 12, 24 and 36 in.
Cannon, J.P., Kiefner, J.F., Munse, W.H.
core
A Review of the Use of Chemical Stabilisation Methods for Lithium‐Ion Batteries
Battery Energy, Volume 4, Issue 5, September 2025.The review reveals that while chemical stabilisation techniques for recycling EOL LIBs are widely used, many studies overlook safety risks, focusing on quick, low‐cost methods. Only a few studies address the associated hazards, highlighting the need for safer, well‐understood stabilisation processes in battery recycling. ABSTRACT The increasing amounts
Mark D. Williams‐Wynn +1 more
wiley +1 more source
The influence of position in overlap joints of Mg and Al alloys on microstructure and hardness of laser welds [PDF]
, 2013 Structure and properties of laser beam welding zone of dissimilar materials, AZ31 magnesium alloy and A5754 Aluminum alloy, are investigated. The microstructure and quality of the Mg/Al weld were studied by metallography, microhardness and optical ...
Fatih H. +10 more
core +6 more sources
Fatigue &Fracture of Engineering Materials &Structures, Volume 48, Issue 9, Page 3859-3878, September 2025.ABSTRACT This research delves into the material performance of submerged arc‐welded S355G10 +M structural steel for offshore wind turbines, with an emphasis on strength, ductility, hardness, distortion, residual stress, and fatigue. This was done by conducting experiments and employing modeling tools combined with image analysis.
Victor Okenyi +7 more
wiley +1 more source
Metallurgy of armour exhibited at the Palace Armoury, Valletta, Malta [PDF]
, 2004 The metallurgy of ten armour pieces from the Palace Armoury Collection in Malta was examined. Results showed that out of ten artefacts examined, six were produced in low carbon steel, one from a high carbon steel and three were made from wrought iron ...
Ashton, John, Hallam, David, Vella, D.
core
Computational Thermodynamics and Kinetics in Materials Modelling and Simulations [PDF]
, 2007 Over the past two decades, Computational Thermodynamics and Kinetics have been tremendously contributed to materials modeling and simulations and the demands on quantitative conceptual design and processing of various advanced materials arisen from ...
Agren, John +6 more
core +2 more sources
Thermodynamic Constraints and Prospects for Intensified Steel Deoxidation
steel research international, Volume 96, Issue 8, August 2025.The article provides a short survey of steel deoxidation and considers how to increase its efficacy. Bringing a specially tailored, powdered slag into the reaction site can directly bind the deoxidation product oxides, resulting in lower dissolved oxygen activity, total oxygen content, and cleaner steel.
Lauri Holappa, Sonja Nurmi
wiley +1 more source
Моделирование процессов межфазного взаимодействия при электродуговой сварке и наплавке под флюсом [PDF]
, 2011 Показано, що для оцінки металургійних властивостей флюсів при електродуговому зварюванні у більшості моделей обмежуються розглядом реакції шлак-метал, що суперечить фізичній моделі електродугового зварювання під флюсом.
core
Analisis Kesalahan Esensial Hasil Pengelasan Peserta Lomba Kompetensi Siswa SMK Tingkat Daerah Istimewa YOGYAKARTA [PDF]
, 2015 The purpose of this study is to examine various defects in the welding joint works from the participants of Vocational High School students' skills competition in Yogyakarta area for welding field.
Djatmiko, R. D. (Riswan) +2 more
core +3 more sources