Results 111 to 120 of about 28,620 (257)

Sustainable Rubberized Concrete-Filled Square Steel Tubular Columns Under Eccentric Compression. [PDF]

Materials (Basel)
Liu Y, Bao Y, Jiang S, Ren Q, Liu Y, Li T.   +5 more
europepmc   +1 more source

Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics

Advanced Engineering Materials, EarlyView.
Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost, Lionel Presmanes, Soléna Colin, Marie Vidal, Sophie Guillemet‐Fritsch   +4 more
wiley   +1 more source

Experimental and statistical investigation on uniaxial compressive performance of hybrid double skin tubular slender columns. [PDF]

Sci Rep
Chandramouli P, Jayaseelan R, Pandulu G, Yaswanth KK.   +3 more
europepmc   +1 more source

Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V

Advanced Engineering Materials, EarlyView.
Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena, Benjamin Bergmann, Michael Zenger   +2 more
wiley   +1 more source

Free and Transient Vibration Analysis of Sandwich Piezoelectric Laminated Beam with General Boundary Conditions. [PDF]

Materials (Basel)
Zhang X, Fu W, Ning Z, Sun N, Li Y, Yang Z, Jiu S.   +6 more
europepmc   +1 more source

The vibration response of a cantilevered rectangular cylinder in cross-flow oscillation [PDF]

, 2004
La´szlo´ Baranyi, Masataka Shirakashi, Mizuyasu Koide, Tsutomu Takahashi, Yuuki Kubo   +4 more
core   +1 more source

Al–Cu Composite Casting of Laser‐Deoxidized Copper: Bonding, Interfacial Chemistry, and Thermal Conductivity

Advanced Engineering Materials, EarlyView.
This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff, Finn‐Lennard Janthur, Sascha Zimmermann, Sarah Seffer, Jörg Hermsdorf, René Gustus, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Christian Klose   +9 more
wiley   +1 more source

Torsional behaviour of high strength steel (S700) rectangular hollow section stub column. [PDF]

Sci Rep
Vanlalruata J, Devi SV, Lalthazuala R.
europepmc   +1 more source

Assessing Altered Coating Adhesion on Plasma‐Deoxidized Surfaces Under Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
This study demonstrates the effectiveness of atmospheric pressure plasma pretreatment in modifying silicon and stainless steel surfaces to improve adhesion. Argon‐hydrogen plasma increases surface roughness and improves adhesion strength, whereas pure argon results in smoother surfaces and structural changes.
Selina Raumel, Lara Kuhr, Khemais Barienti, Sebastian Herbst, Florian Nürnberger, Hans Jürgen Maier, Marc C. Wurz   +6 more
wiley   +1 more source

Effects of low cycle fatigue and inelastic buckling on the superelasticity and energy dissipation capacity of NiTi SMA rebar. [PDF]

J Intell Mater Syst Struct
Mohammadgholipour A, Billah AM.
europepmc   +1 more source