Results 161 to 170 of about 159,943 (267)

A Double Decomposition of Standard Deviation Below the Modal Age at Death and the Role of Causes of Death. [PDF]

Eur J Popul
Diaconu V, Zarulli V, Mazzuco S.
europepmc   +1 more source

Influence of Geometric Design on Mechanical Performance of Auxetic Metastructure

Advanced Engineering Materials, EarlyView.
Strategic geometric reinforcement transforms auxetic performance. This study evaluates 3D‐printed arrowhead metastructures, revealing that a modified design with local ring reinforcement suppresses premature failure to achieve superior energy absorption and structural efficiency.
Muhammad Gulzari, Supharoek Sornsomrit, Muhammad Ayaz Akbar, Stephan Rudykh   +3 more
wiley   +1 more source

Multidecadal preindustrial methane variability can be explained by noise in the source-sink imbalance. [PDF]

Proc Natl Acad Sci U S A
Mei EJ, Hakim GJ, Proistosescu C, Bauska TK, Buizert C, Turner AJ.   +5 more
europepmc   +1 more source

Inverse Identification of Energy‐Dependent Laser Absorptivity in NiTi Laser Powder‐Bed Fusion via Calibrated Melt Pool Simulation

Advanced Engineering Materials, EarlyView.
A combined experimental–computational framework identifies energy‐dependent laser absorptivity for NiTi in laser powder‐bed fusion, applicable to conduction and transition modes. Single‐track experiments and thermofluid smoothed particle hydrodynamics simulations are coupled through inverse analysis of melt pool geometry.
Mohamadreza Afrasiabi, Hadi Moutablaleh, Ignatius A. Setiawan, Mehrshad Mehrpouya   +3 more
wiley   +1 more source

Identification of high-risk cells in single-cell spatially resolved transcriptomics data using Diagnostic Evidence GAuge of Single-cells with spatial smoothing. [PDF]

Bioinformatics
Chatterjee D, Couetil JL, Liu Z, Huang K, Chen C, Zhang J, Kalwat MA, Johnson TS.   +7 more
europepmc   +1 more source

Experimental Characterization of Mycelium‐Based Composites Under Multiple Loading Conditions

Advanced Engineering Materials, EarlyView.
This study examines the mechanical response of mycelium‐based composites under compression, shear, and tension using mechanical testing and imaging methods. The comparison between unpressed and hot‐pressed specimens shows that hot pressing is associated with higher compression and shear stiffnesses.
Shaghayegh Elahi, Kimiya Tajik, Harvey Shaw, Matti Isakov, Sami Pajunen, Lauri Rautkari   +5 more
wiley   +1 more source

Rapid Assessment of Italian Honey Chemical Composition and Botanical Origin Using NIR Spectroscopy Coupled with Chemometric Analysis. [PDF]

Sensors (Basel)
Zoroaster A, Calore A, Sobhani A, Dainese N, Granato A, Segato S, Serva L.   +6 more
europepmc   +1 more source

Compatibility of Methacrylate Based Resins Controls Interfacial Failure and Toughness in 3D‐Printed Multimaterial Composites

Advanced Engineering Materials, EarlyView.
This work shows that the mechanical performance of multimaterial digital light processing (DLP) printed thermoset composites is governed by resin compatibility and interfacial design rather than spatial patterning alone. Brittle and ductile resin combinations produced premature interfacial failure, while graded interfaces and mechanically compatible ...
Ahmed M. H. Ibrahim, Li Meng, Ahmad R. Najafi, Nicolas J. Alvarez   +3 more
wiley   +1 more source

Uncertainty-Aware Probabilistic Fusion Post-Processing for Continuous Wrist Motion Estimation in Myoelectric Control. [PDF]

Sensors (Basel)
Feng S, Xu G, Li Y.
europepmc   +1 more source

Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading

Advanced Engineering Materials, EarlyView.
This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev, Noah‐Lean Roschlaub, Anne Jung   +2 more
wiley   +1 more source