Results 191 to 200 of about 1,958,921 (299)

Experimental Evaluation of 100Cr6 Steel Microindented Surfaces Under Lubricated Nonconformal Point Contacts

Advanced Engineering Materials, EarlyView.
The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi, Pasquale Guglielmi, Gianfranco Palumbo, Giuseppe Carbone   +3 more
wiley   +1 more source

Assessing the Reliability of the ORADIII (Oral Radiology Artificial Intelligence Diagnostic - Version 3) Software Application in Rendering a Diagnosis: A Retrospective Study. [PDF]

Cureus
Muttanahally KS, Gonzalez J, Crocker GP, Narayana N.   +3 more
europepmc   +1 more source

Software Reliability: Metrics

International Journal of Computer Applications, 2016
Pallavi P., Durga Patel
openaire   +1 more source

What Do Large Language Models Know About Materials?

Advanced Engineering Materials, EarlyView.
If large language models (LLMs) are to be used inside the material discovery and engineering process, they must be benchmarked for the accurateness of intrinsic material knowledge. The current work introduces 1) a reasoning process through the processing–structure–property–performance chain and 2) a tool for benchmarking knowledge of LLMs concerning ...
Adrian Ehrenhofer, Thomas Wallmersperger, Gianaurelio Cuniberti   +2 more
wiley   +1 more source

A Tutorial on Sample Size Calculation for Inter-rater and Intra-rater Agreement Studies. [PDF]

Indian J Psychol Med
Madadizadeh F, Bahariniya S.
europepmc   +1 more source

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source

A high-performance onboard computing architecture for autonomous satellite mission planning. [PDF]

Sci Rep
Rao J, Zhao W, Ma M, Xue G, Zhang J, Li S, Zhu Y, An J.   +7 more
europepmc   +1 more source

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source

Validation and reliability of Kinovea video analysis for temporomandibular and cervical range of motion in children with spastic cerebral palsy. [PDF]

Front Bioeng Biotechnol
Baykan Çopuroğlu Ö, Tuğay BU, Vatan MF.   +2 more
europepmc   +1 more source

Prediction of Surface Topography Parameters in Direct Laser Interference Patterning of Stainless Steel Using Infrared Monitoring and Convolutional Neural Networks

Advanced Engineering Materials, EarlyView.
This study presents an infrared monitoring approach for direct laser interference patterning (DLIP) combined with a convolutional neural network (CNN). Thermal emission data captured during structuring are used to predict surface topography parameters.
Lukas Olawsky, Marcelo Sallese, Leander Kläber, Clemens Kuhn, Keming Du, Andrés Fabián Lasagni   +5 more
wiley   +1 more source