Results 241 to 250 of about 694,702 (336)

Formamidinium Incorporates into Rb-based Non-Perovskite Phases in Solar Cell Formulations. [PDF]

Angew Chem Int Ed Engl
Gunes U, Hope MA, Zhang Y, Zheng L, Pfeifer L, Grätzel M, Emsley L.   +6 more
europepmc   +1 more source

Preparation and characterization of hydrogenated amorphous boron thin films and thin film solar cells produced by glow discharge decomposition methods. Third quarterly progress report, July 1, 1979-September 30, 1979

, 1979
F. H. Cocks, P. L. Jones, L. J. Dimmey
openalex   +2 more sources

Electrochemically Driven Tandem In‐Plane Reduction and FeCl3‐ Intercalation of Highly Crystalline Graphene Oxide Thin Films

Advanced Functional Materials, EarlyView.
This study presents a green processing route for high‐performance reduced graphene oxide (rGO) transparent conductive films (TCFs) using highly crystalline Brodie's GO. In‐plane electrochemical reduction forms rGO on insulating substrates without toxic reductants or heat. Subsequent FeCl₃ intercalation enhances conductivity, overcoming the transparency–
Tatsuki Tsugawa, Kazuto Hatakeyama, Junya Kawasaki, Agamoni Pathak, Kazuhito Tsukagoshi, Shintaro Ida, Takaaki Taniguchi   +6 more
wiley   +1 more source

Comparison of organic and inorganic hole transport layers in double perovskite material-based solar cell. [PDF]

Beilstein J Nanotechnol
K D, Singh A.
europepmc   +1 more source

Device physics for engineering design of heavily doped regions in pn-junction silicon solar cells / by Muhammed Ayman Shibib.

, 1979
M.A. Shibib
openalex   +2 more sources

Additive‐Driven Phase Control for Stable and Efficient CsPbI₃ Solar Cells Via Ambient Low‐Temperature Processing

Advanced Functional Materials, EarlyView.
CsPbI₃ perovskite solar cells face stability issues due to high annealing temperatures and moisture. Butylammonium acetate (BAAc) enables stable phase formation at 160°C in ambient laboratory conditions, enhancing efficiency and stability, achieving 18.6% PCE, and maintaining over 81% efficiency after 1,000 hours of maximum power point tracking under 1
Narendra Pai, Aaron Seeber, Wen Liang Tan, Luke J. Sutherland, Chris Easton, Wenqi Yan, Yogesh Gulia, Yesim Gozukara, Jueng‐Eun Kim, Mei Gao, Dechan Angmo   +10 more
wiley   +1 more source

Performance evaluation of Cu₂SrSnS₄ based solar cell: effect of transition metal dichalcogenides buffer layer. [PDF]

Sci Rep
Mebrek H, Zaidi B, Mekhaznia N, Al-Dmour H, Barkhordari A.   +4 more
europepmc   +1 more source

Design and fabrication of solar cell modules. Final technical report

, 1978
Tom Shaughnessy
openalex   +2 more sources

Colloidal Opaline Composites as Throughput‐Scalable, Fully Transparent, and Color‐Tunable Radiative Cooling Exterior Films for Outdoor Photovoltaics

Advanced Functional Materials, EarlyView.
Particular thermal metamaterials are widely used as daytime radiative coolers merely by embedding thermally emissive nanoparticles (NPs) in liquid resins to form scalable, yet highly efficient cooling films in a cost‐effective way. However, randomly dispersed NPs, prevalently used thus far, cause strong scattering, limiting NP content and cooling ...
YongDeok Cho, Hyeon Ho Kim, Sewon Ahn, Jaewon Lee, Jieun Lee, Kwangjin Kim, Soyul Kwak, Hoodam Lee, Kyungsik Choi, Kyonghwa Song, Seungwoo Lee   +10 more
wiley   +1 more source

Impact of a Thin Sacrificial Mo Layer on the Formation of the Wide Band Gap ACIGSe Absorber/ITO Thin-Film Solar Cell Interface. [PDF]

ACS Appl Mater Interfaces
Demling A, Gutzler R, Almeida Alves CF, Wilks RG, Félix R, Hariskos D, Paetel S, Cerqueira R, Sadewasser S, Witte W, Bär M.   +10 more
europepmc   +1 more source