Results 121 to 130 of about 20,335,239 (286)

Microscale metal additive manufacturing by solid-state impact bonding of shaped thin films

Small
Abstract The deposition of device-grade inorganic materials is one key challenge towards the implementation of additive manufacturing in microfabrication, and to that end, a broad range of physico-chemical principles has been explored for 3D fabrication with micro- and nanoscale resolution. Yet, for metals, we still lack a process that achieves
Alain Reiser, Christopher Schuh
openaire   +4 more sources

Inverse Identification of Energy‐Dependent Laser Absorptivity in NiTi Laser Powder‐Bed Fusion via Calibrated Melt Pool Simulation

Advanced Engineering Materials, EarlyView.
A combined experimental–computational framework identifies energy‐dependent laser absorptivity for NiTi in laser powder‐bed fusion, applicable to conduction and transition modes. Single‐track experiments and thermofluid smoothed particle hydrodynamics simulations are coupled through inverse analysis of melt pool geometry.
Mohamadreza Afrasiabi, Hadi Moutablaleh, Ignatius A. Setiawan, Mehrshad Mehrpouya   +3 more
wiley   +1 more source

A Comprehensive Review of Solid-phase Additive Techniques: Insights into Friction Stir Additive Manufacturing (FSAM) and Additive Friction Stir Deposition (AFSD)

Results in Engineering
Additive Manufacturing (AM) is increasingly being used in the aerospace and automotive sectors because of its ability to produce lightweight, high-performance components while minimising material waste and lowering buy-to-fly ratios. Among the several AM
Nouranga K. N., Prashanth B. N., Ram Prabhu T.   +2 more
doaj   +1 more source

Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading

Advanced Engineering Materials, EarlyView.
This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev, Noah‐Lean Roschlaub, Anne Jung   +2 more
wiley   +1 more source

Phase-field modeling and Experimental investigation for rapid solidification in wire and arc additive manufacturing

Journal of Materials Research and Technology
The rapid solidification speed and significant temperature gradient observed in the wire and arc additive manufacturing (WAAM) process result in a deviation of the solid-liquid interface from the equilibrium state assumed by the conventional directional ...
Fuchen Wang, Weipeng Chen, Dong Wang, Hua Hou, Yuhong Zhao   +4 more
doaj   +1 more source

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

Advanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati, Karthik Kumar Banku, Prasanth Bondi, Ivan Zhirnov, Yangyiwei Yang, Gordon Schmidt, Jürgen Christen, Georg Hasemann, Manja Krüger, Bai‐Xiang Xu, Bilal Gökce, Silja‐Katharina Rittinghaus   +11 more
wiley   +1 more source

Une méthodologie de conception pour la fabrication additive [PDF]

, 2011
Résumé - Les méthodologies de Design for Assembly et de Design for Manufacturing visent à rendre les produits plus faciles à fabriquer et à assembler en se basant sur les caractéristiques des procédés actuels de fabrication, toutefois ces ...
RODRIGUE, Hugo, CALATORU, Victor, RICHIR, Simon, RIVETTE, Mickaël   +3 more
core   +1 more source

Impact of MgO Additions on the Oxidation Resistance and Compression Behavior of Vanadium Alloys

Advanced Engineering Materials, EarlyView.
An increase in oxidation resistance at 600 °C is achieved for alloys containing more than 2.5 wt.% MgO. It has been established that, along with V2O5, MgO6V2, and Mg2O7V2 are formed, which are presumed to enhance oxidative stability. Furthermore, the possible transformation of Mg‐vanadates through reaction with CO2, which presumably occurs in this ...
Ievgen Solodkyi, Mathias Galetz, Georg Hasemann, Fabian Lanoy, Emma White, Manja Krüger   +5 more
wiley   +1 more source

Manipulating ionic conductivity through chemical modifications in solid-state electrolytes prepared with binderless laser powder bed fusion processing

JPhys Energy
Additive manufacturing of solid-state batteries is advantageous for improving the power density by increasing the geometric complexity of battery components, such as electrodes and electrolytes.
Katherine A Acord, Alexander D Dupuy, Qian Nataly Chen, Julie M Schoenung   +3 more
doaj   +1 more source

The Additive Manufacturing of Glass: A Critical Review

Applied Sciences
This paper presents a critical review of additive manufacturing (AM) techniques applied to glass, elucidating the current state of the field and identifying key challenges and opportunities.
Mackinley Shaw, Dylan Vlahopoulos, Clara Usma-Mansfield, Jeffrey Sarmiento, Roland Snooks, Tony Koutsonikolas, Nick Birbilis   +6 more
doaj   +1 more source