Results 161 to 170 of about 20,335,239 (286)

Programmable Porosity in Polymers via Microfluidic Templating and 3D Printing. [PDF]

Small Methods
Serpe F, Angelini R, Barbetta A, Rosciardi V.   +3 more
europepmc   +1 more source

Impact of the Process Atmosphere During Hot Isostatic Pressing on the Near‐Surface Composition of an Additively Manufactured Austenitic High‐Interstitial Steel

Advanced Engineering Materials, EarlyView.
A high interstital austenitic steel is additively manufactured and postdensified by HIP to eliminate gas porosity. Thereby, the loss of N and Mn in Ar HIP atmosphere is investigated. Further, HIP using N2 atmosphere is investigated which led to excessive nitride formation.
F. Großwendt, J. Hahn, J. Kimm, S. Weber, J. Lentz   +4 more
wiley   +1 more source

Application and Adaptation of Arc-Based Welding Processes to Wire Arc Additive Manufacturing: A Review. [PDF]

Materials (Basel)
Elalem AN, Alrehaili H, Alam MA, Raja S, Uddin A.   +4 more
europepmc   +1 more source

Anticorrosive Performance of Smart Epoxy Coatings With Poly(urea‐formaldehyde) Microcapsules Filled With 5‐Ethylidene‐2‐norbornene

Advanced Engineering Materials, EarlyView.
PUF/ENB microcapsules were synthesized based on a sequential factorial design and incorporated into an epoxy matrix. Their anticorrosive action, associated with the self‐healing mechanism, demonstrated that the addition of microcapsules to the coating improved anticorrosive performance compared to pure epoxy coatings, particularly when the encapsulate ...
Vandicleya Alves Moreira, Maria Paula de Carvalho Freire, Ygor Matheus Pereira de Paula, Ana Leticia Santos, Alice da Costa Silva, Nicolau Apoena Castro, Maria Carolina Burgos Costa   +6 more
wiley   +1 more source

Editorial for the Special Issue on Advanced Micro- and Nano-Manufacturing Technologies, 2nd Edition. [PDF]

Micromachines (Basel)
Li K.
europepmc   +1 more source

Mitigating Creep Anisotropy and Enhancing Performance in Additively Manufactured Ni‐Based Superalloys: A Review

Advanced Engineering Materials, EarlyView.
Additive manufacturing introduces pronounced microstructural and crystallographic anisotropy in Ni‐based superalloys, resulting in orientation‐dependent creep deformation and damage. This review identifies the key microstructural origins of creep anisotropy, examines their influence on dominant deformation mechanisms, and highlights processing ...
Chandan Kumar, Shobhit Pratap Singh, Gaurav Mohanty, Praveen Kumar   +3 more
wiley   +1 more source

Methods of porous and foamed structure formation in geopolymer-based materials: a comprehensive review. [PDF]

RSC Adv
Goryunova K, Gahramanli Y.
europepmc   +1 more source

Electrodeposition in Structural Lattices of Variable Architectures

Advanced Engineering Materials, EarlyView.
Electrodeposition enables geometry‐sensitive, autonomous void filling while simultaneously tuning chemical and mechanical properties. The development of approaches that can autonomously fill and heal material voids and yield composites with tailorable properties is increasingly relevant in engineering.
Yeong‐Man Kwon, Jingwen Zhang, Guido Musso, Alessandro F. Rotta Loria   +3 more
wiley   +1 more source

Research Progress on Defect Behavior, Microstructure, and Service Performance of Additively Manufactured Austenitic Stainless Steels. [PDF]

Materials (Basel)
Liu K, Dong H, Zhang L.
europepmc   +1 more source

Microstructure‑Dependent Phase Transformations Under High‑Pressure Laser Heating in Additively Manufactured AlCrFe2Ni2

Advanced Engineering Materials, EarlyView.
Additively manufactured AlCrFe2Ni2 with contrasting BCC/B2‐dominant and lamellar FCC + BCC/B2 microstructures exhibits the same pressure‐induced BCC/B2 → HCP transformation. Under laser heating at high pressure, HCP is destabilized, and a cubic BCC/B2 + FCC assemblage is recovered, while the lower‐scan‐speed microstructure transforms at a lower ...
Raimundas Sereika, Hunter Kantelis, Yogesh K. Vohra, Shengbiao Zhang, Wuxian Yang, Wen Chen   +5 more
wiley   +1 more source