Results 191 to 200 of about 516,633 (247)
Some of the next articles are maybe not open access.

Solidification Behaviour of the Al2Cu Phase

International Journal of Materials Research, 1996
The A1-Cu phase diagram was redetermined in the concentration range between 31 and 37.5 at.% Cu applying differential thermal analysis, magnetothermal analysis and optical microscopy. The solubility of the Al 2 Cu phase which is formed in a peritectic reaction at 592° C ranges at 549° C from 32.05 to 32.6 at.% Cu and at 250° C from 32.4 to 32.8 at.% Cu.
Tilo Gödecke, Ferdinand Sommer
openaire   +1 more source

Solidification and leaching behaviours of Cr6+ in sludge ceramsite

Journal of Hazardous Materials, 2008
Making lightweight ceramsite with sewage sludge is a new effective approach for disposal of sludge. However, there is a concern as to whether the heavy metals such as Cr6+ in sewage sludge can be solidified in ceramsite after sintering. The configuration of Cr6+ in ceramsite was analyzed by X-ray diffraction (XRD) and leaching tests were conducted to ...
G R, Xu, J L, Zou, G B, Li
openaire   +2 more sources

A complexity in the solidification behaviour of molten Y3Al5O12

Journal of Crystal Growth, 1979
At high degrees of undercooling, it is shown that the solidification behaviour of molten Y3Al5O12 can depart substantially from that predicted by the equilibrium-phase relationships. This leads to the formation of a two-phase perovskite/α-alumina mixture, which is ceramic and opaque in appearance, in preference to transparent garnet material obtained ...
B. Cockayne, B. Lent
openaire   +1 more source

Solidification behaviour of droplets in spray deposition

Powder Metallurgy, 2005
In spray deposition, a stream of molten metal is atomised with an inert gas to form a spray of molten droplets; these are then accelerated towards a substrate where they impinge and consolidate. Near-net shape products can be manufactured by technologies involving solidification and droplet consolidation. In order to maximise the metallurgical benefits
S. N. Sahu, S. Harikishore, S. C. Koria
openaire   +1 more source

Facetting behaviour of Al2Cu during solidification

Journal of Crystal Growth, 1981
Abstract The shapes of the solid-liquid interfaces of Al2Cu in front of various Al-Cu liquid alloys were observed using in situ electron microscopy during solidification or scanning electron microscopy afterwards. The change in morphology (from non faceted at the eutectic composition to faceted at the Al2Cu composition) allowed us to sort the facets ...
R. Hamar, C. Lemaignan
openaire   +1 more source

Solidification behaviour of undercooled equiatomic FeCuNi alloy

Journal of Alloys and Compounds, 2020
Abstract Studies on solidification of equiatomic multi-component alloys are essential in developing melt-route processing of high entropy alloys. The extent of undercooling during processing controls microstructure evolution. In this study, we present solidification studies on undercooled equiatomic FeCuNi alloy carried out using melt fluxing ...
M.R. Rahul, Gandham Phanikumar
openaire   +1 more source

Solidification behaviour of TiAl-based alloys studied by directional solidification technique

Intermetallics, 2011
Abstract Solidification behaviour of TiAl-based alloys with the nominal chemical composition Ti–46Al–8Ta and Ti–46Al–8Nb (at.%) was studied at steady- and unsteady-state conditions in Y 2 O 3 moulds using Bridgman solidification technique. The effect of growth parameters (growth rate V and temperature gradient G L ) on primary solidification ...
J. Lapin, Z. Gabalcová
openaire   +1 more source

Solidification Behaviour of a H21 Tool Steel

Advanced Materials Research, 2014
Solidification behaviour of a H21 tool steel has been studied. The aim of this work is to give better understanding of the as cast microstructure of the steel. The investigated H21 tool steel was made using induction vacuum furnace with air cooling. The microstructure observation was carried out using optical and electron microscopy.
Meilinda Nurbanasari   +2 more
openaire   +1 more source

Solidification behaviour in plasma are welding

Sadhana, 2001
Melting and solidification behaviour in the deep penetrution welding process is different from that in conventional welding process in deep penetration processes there is keyhole formation and the full thickness of the plate receives the are heat input unlike conventional processes in which the heat input is received only by the surface nodes.
openaire   +1 more source

Solidification and flow behaviour of mould fluxes

2002
Mould fluxes are synthetic slags added to the molten steel surface in the copper mould and provide lubrication by melting and infiltrating the gap between the solidified steel and mold. The use of mould lubricants in continuous casting of steel has been an important operational measure since the inception of continuous casting as early as the 1940's ...
Brooks, Geoffrey   +2 more
openaire   +1 more source

Home - About - Disclaimer - Privacy