Results 21 to 30 of about 516,633 (247)

Thermal analysis applied to estimation of solidification kinetics of Al–Si aluminium alloys [PDF]

open access: yes, 2009
Evaluation of solidification kinetics by thermal analysis is a useful tool for quality control of Al–Si melts before pouring provided it is rapid and highly reproducible.
Loizaga, Aitor   +7 more
core   +1 more source

HYDRAULIC BEHAVIOUR OF HIGLEIG-PORTSUDAN PIPELINE AT OPERATION AND SHUTDOWN CONDITIONS [PDF]

open access: yesJournal of Engineering Science and Technology, 2014
Experimental measurements were carried out to correlate rheological properties of Nile blend with temperature within temperature ranges at which Nile blend exhibits Newtonian, non-Newtonian, and solidification behaviours.
MYSARA EISSA MOHYALDINN
doaj  

New approaches to casting hypereutectic Al-Si alloys to achieve simultaneous refinement of primary silicon and modification of eutectic silicon [PDF]

open access: yes, 2013
This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel UniversityHypereutectic Al-Si alloys are of increasing interest for applications that require a combination of light weight and high wear resistance, such as pistons ...
Al-Helal, Kawther
core   +5 more sources

Colour Metallography of Cast Iron - Chapter 1: Introduction (Ⅰ) [PDF]

open access: yesChina Foundry, 2009
Cast iron, as a traditional metal material, has advantages of low total cost, good castability and machinability, good wear resistance and low notch sensitivity, and is still facing tough challenge in quality, property and variety of types etc.
Zhou Jiyang
doaj  

Colour Metallography of Cast Iron - Chapter 3: Spheroidal Graphite Cast Iron (Ⅲ) [PDF]

open access: yesChina Foundry, 2010
Cast iron, as a traditional metal material, has advantages of low total cost, good castability and machinability, good wear resistance and low notch sensitivity, and is still facing tough challenge in quality, property and variety of types etc.
Zhou Jiyang
doaj  

Colour Metallography of Cast Iron - Chapter 5: White Cast Iron (Ⅰ) [PDF]

open access: yesChina Foundry, 2011
Cast iron, as a traditional metal material, has advantages of low total cost, good castability and machinability, good wear resistance and low notch sensitivity, and is still facing tough challenge in quality, property and variety of types etc.
Zhou Jiyang
doaj  

Colour Metallography of Cast Iron - Chapter 3: Spheroidal Graphite Cast Iron (Ⅱ) [PDF]

open access: yesChina Foundry, 2010
Cast iron, as a traditional metal material, has advantages of low total cost, good castability and machinability, good wear resistance and low notch sensitivity, and is still facing tough challenge in quality, property and variety of types etc.
Zhou Jiyang
doaj  

On the formation of microstructural gradients in a nickel-base superalloy during electron beam melting

open access: yesMaterials & Design, 2018
Electron beam melting (EBM) is one of the most widely used additive manufacturing (AM) methods for metallic components and has demonstrated great potential to fabricate high-end components in the aerospace and energy industries.
Dunyong Deng   +3 more
doaj   +1 more source

Colour Metallography of Cast Iron - White Cast Iron (Ⅱ) [PDF]

open access: yesChina Foundry, 2011
Cast iron, as a traditional metal material, has advantages of low total cost, good castability and machinability, good wear resistance and low notch sensitivity, and is still facing tough challenge in quality, property and variety of types etc.
Zhou Jiyang
doaj  

Colour Metallography of Cast Iron - Chapter 2: Grey Iron (Ⅱ) [PDF]

open access: yesChina Foundry, 2009
Cast iron, as a traditional metal material, has advantages of low total cost, good castability and machinability, good wear resistance and low notch sensitivity, and is still facing tough challenge in quality, property and variety of types etc.
Zhou Jiyang
doaj  

Home - About - Disclaimer - Privacy