Results 131 to 140 of about 76,483 (275)
Numerical study of an exhaust heat recovery system using corrugated tubes and twisted tape inserts [PDF]
, 2014 Thesis (M.S.) University of Alaska Fairbanks, 2014Diesel engine generators are the major power source for small communities in cold regions. Diesel generators waste about 1/3 of their fuel energy in the form of heat through exhaust gas.
Mokkapati, Vamsi Krishna Sarma
core
Highly Dynamic Soft Electrohydraulic Origami Actuators for Agile and Multimodal Robotic Locomotion
SmartBot, EarlyView.Most current soft robots still lag far behind their natural counterparts in both agility and speed, mainly attributed to the limited morphing modes and performance of soft actuators. Here, the authors report a new methodology of electrohydraulic origami (EHO) for creating powerful and multimodal soft actuators with large strain, high speed, lightweight,
Wenbo Li +6 more
wiley +1 more source
steel research international, EarlyView.Laser powder bed fusion of JIS SKD61 tool steel is systematically optimized using a Taguchi design and ANOVA. Hatch spacing and layer thickness are identified as dominant parameters controlling surface roughness and tensile strength. Subsequent tempering at 600°C improves microstructural stability and mechanical performance, enabling high‐density SKD61
Masrurotin Masrurotin +4 more
wiley +1 more source
Model‐Based Systems Engineering in Space Applications: A Comprehensive Literature Review
Systems Engineering, EarlyView.ABSTRACT The growing complexity of space engineering is driving the demand to embrace the adoption of Model‐Based Systems Engineering (MBSE). Although the MBSE is well‐practiced in the space industry, the level of effort and need required to obtain the benefits of MBSE vastly differ across enterprises; this disparity presents a significant challenge to
Rehobot Bekele Buruso +4 more
wiley +1 more source
Portable Radar for Noncontact Heart Rate Monitoring and Estrus Detection in Dairy Cows
IEEJ Transactions on Electrical and Electronic Engineering, EarlyView.This study introduces a portable radar system for real‐time monitoring of respiratory and heart rates in dairy cows. It uses millimeter‐wave Frequency Modulated Continuous Wave (FMCW) radar to perform noncontact physiological sensing, reducing behavioral disturbance. The radar system's design prioritizes portability, cost‐effectiveness, and robustness,
Yingxiu Li +7 more
wiley +1 more source
Andrology, EarlyView.ABSTRACT Background Infertility is a pressing global health concern, affecting one in six couples worldwide. The failure rate for assisted reproductive technologies (ART) cycles remains at approximately 78%, with limited improvements often attributed to a lack of technological innovation.
Mehran Dabiri +3 more
wiley +1 more source
3D printing in core facilities – Low pain, high gain
Journal of Microscopy, EarlyView.Abstract Three‐dimensional (3D) printing has rapidly developed from a niche hobbyist activity into a widely accessible and indispensable technology across multiple scientific disciplines. Within microscopy, optical engineering laboratories and imaging core facilities, 3D printing enables creating customised solutions for sample holders, optical ...
Mohammad Goudarzi +5 more
wiley +1 more source
Revista Facultad de Ingeniería Universidad de Antioquia, 2016 Los robots son sistemas electromecánicos que necesitan enfoque mecatrónico antes de fabricarlos, esto con el fin de reducir el costo de desarrollo.
Saravana Mohan Mariappan +1 more
doaj
Journal of Prosthodontics, EarlyView.Abstract Purpose This study aims to characterize the mechanical properties of implant‐supported full arch fixed complete dentures manufactured by milling and injection techniques. Materials and Methods Twenty‐two samples with milling and injection manufacturing techniques were fabricated.
Mustafa Gürkan +7 more
wiley +1 more source
Journal of Prosthodontics, EarlyView.Abstract Purpose In metal–ceramic restorations, the substructure fabrication method and design may affect the prognosis of the prosthesis. This study evaluated and compared the fracture resistance of metal–ceramic restorations fabricated with different substructure fabrication methods using two different alloy powders and designs.
Young‐Hoon Lee +4 more
wiley +1 more source