Results 51 to 60 of about 11,346 (236)

Substantiation of Geometric Parameters of a Variable Inertia Moment Pulley

Nauka ta progres transportu, 2023
Purpose. The main purpose of our work is to substantiate the geometric parameters of a variable moment of inertia pulley, which can reduce the weight of a drive with such a pulley. Methodology.
Olek. S. Kuropiatnyk, M. Y. Sharapov
doaj   +1 more source

Large‐Scale and Cost‐Effective Fabrication of Ultra‐Thin, Biodegradable Microelectrode Arrays and Pressure Sensors Using Laser Micromachining

Advanced Materials Technologies, EarlyView.
A mask‐free and cost‐effective UV‐pico‐second laser‐based microfabrication method is proposed to fabricate large‐area biodegradable microelectrode arrays and pressure sensors. These devices demonstrate low impedance, good conformability, excellent biocompatibility, and rapid degradation, providing a new route for next‐generation transient electronics ...
Bhavani Prasad Yalagala, Asfand Tanwear, María Cerezo‐Sánchez, Hossein Parvizi, Morteza Amjadi, Hadi Heidari   +5 more
wiley   +1 more source

Additively Manufactured Porous Ceramics as Tunable Dielectrics for Passive Temperature Sensing

Advanced Materials Technologies, EarlyView.
Porous ceramic lattices, 3D‐printed from a multicomponent oxide ink, are integrated with LC resonators for passive wireless temperature sensing. By tuning porosity, the dielectric properties and RF response are engineered to produce distinct resonant frequency shifts with temperature. The results establish a structure‐driven approach to customizing the
Sogol Heidarishahrivar, Aminul Islam, Chang Woo Gal, Insup Kim, Yeong‐Jin Choi, Woo Soo Kim   +5 more
wiley   +1 more source

Study of the Effect of Bulb Ratio and Blade Angle on Propeller Turbine Performance in Horizontal Flow using Numerical Simulation

Teknik, 2020
This paper discusses numerical simulations of horizontal flow propeller turbines. Static bulbs located before the turbine can be used to increase water velocity and potentially increase the turbine's performance.
Akhmad Nurdin, Dwi Aries Himawanto, Syamsul Hadi   +2 more
doaj   +1 more source

Fully 3D‐Printed Wave‐Wound Electromagnetic Motors

Advanced Materials Technologies, EarlyView.
This work presents the first fully 3D‐printed wave‐wound electromagnetic motors, which are created using conductive nanoparticle inks, carbon‐filled nylon polymers, and surface mount components. These motors can achieve a stall torque of 7.62N·mmA−1$7.62 \nobreakspace N{\cdot }mm A^{-1}$ and efficiency of 28.2 %, which approaches the performance of ...
Joseph Schwalbe, Sebastian Mettes, Eduardo Francke, Kenneth W. Allen, Yi Chen Mazumdar   +4 more
wiley   +1 more source

Application of SolidWorks software in preoperative planning of high tibial osteotomy

Frontiers in Surgery, 2023
PurposeOpen-wedge high tibial osteotomy (HTO) is a common surgical treatment for medial osteoarthritis in young and active patients. The accuracy of osteotomy is closely associated with postoperative efficacy.
Yufeng Lu, Xue Wang, Bo Yang, Zhaochen Xu, Baogang Zhang, Bin Jia, Jinlong He, Liang Qi, Min Wang, Feng Qiao   +9 more
doaj   +1 more source

A Soft Robotic Device for Targeted Massage Therapy of Residual Limbs

Advanced Robotics Research, EarlyView.
Residual limb edema after amputation can hinder recovery and delay prosthetic fitting. This study presents a soft‐robotic wearable device that delivers sequential compression through pneumatic McKibben actuators. By replicating the principles of manual lymphatic drainage, the device generates controlled mechanotherapeutic pressure patterns, providing a
Maria Grazia Polizzotto, Alessio Capecchi, Maartje Van der Lingen, Emanuele Gruppioni, Arianna Menciassi, Linda Paternò   +5 more
wiley   +1 more source

Origami‐Inspired Structural Design for Aquatic‐Terrestrial Amphibious Robots

Advanced Robotics Research, EarlyView.
This work presents a lightweight amphibious origami robot actuated by a single shape memory alloy wire. A rigid foldable origami structure with displacement amplification enables efficient terrestrial crawling and aquatic swimming. The addition of fan‐shaped units allows controllable turning in both environments.
Weiqi Liu, Chunlong Wang, Xiaohang Sun, Hongwei Guo, Jiayao Ma, Yan Chen   +5 more
wiley   +1 more source

Grip and Grasp: Lizard Claw Inspired Robotic Manipulators

Advanced Robotics Research, EarlyView.
Our study identifies the most effective lizard claw shape for use as an end effector in a bioinspired robotic manipulator. By examining key geometric features and combining them into comparative indices, the Crotaphytus collaris claw is found to be the best fit.
Hyeon Lee, Kate Douglas, Asyiah Bray, Andrea Rummel, Parvez Alam   +4 more
wiley   +1 more source

Bioinspired Soft‐Skeleton Robotics With Cooperative Shape Transformation and Stiffness Adaptation

Advanced Robotics Research, EarlyView.
A bioinspired soft‐skeleton robot that integrates variable‐stiffness chain skeletons into a soft textile skin is developed. The chain skeletons are highly flexible initially but can stiffen upon pneumatic actuation, enabling large deformation and enhanced load‐bearing capacity.
Mengyuan Niu, Xiaorui Hu, Chenmin Yuan, Haoyun Li, Xuzhong Su, Fengxin Sun   +5 more
wiley   +1 more source