Results 181 to 190 of about 30,463 (266)

Hydrogen‐Assisted Fracture of Iron‐Based Fe–Ni–Al Alloys

Advanced Engineering Materials, EarlyView.
Principal relations and fracture mechanisms of single‐phase and precipitate‐strengthened Fe–Ni–Al alloys subjected to prior electrochemical hydrogen charging are identified. The mechanisms of hydrogen effect on strength and microhardness are discussed, including hydrogen‐induced increase in microhardness and the role of hydrogen in fracture behavior ...
Nataliya Yadzhak, Olha Zvirko, Rostyslav Leshchak, Hryhoriy Nykyforchyn   +3 more
wiley   +1 more source

Slip Localization Intensification Mediated by Grain Boundary Sliding in a Polycrystalline Nickel‐Based Superalloy

Advanced Engineering Materials, EarlyView.
The temperature dependence of fatigue behavior in nickel‐based superalloys is investigated through high‐resolution measurements of plastic localization. While increasing temperature reduces localization and enhances fatigue performance in René 88DT, Inconel 718 exhibits a sharp degradation at intermediate temperature due to intensified slip ...
M. Calvat, D. Anjaria, I. Woo, C. Bean, D. Texier, J. C. Stinville   +5 more
wiley   +1 more source

Creep‐Induced Microstructural Evolution in an A2‐B2 Superalloy

Advanced Engineering Materials, EarlyView.
A 27.3Ta‐27.3Mo‐27.3Ti‐8Cr‐10Al (at.%) refractory high‐entropy alloy with precipitation‐strengthened A2‐B2 microstructure was studied by creep tests at 1030°C, which demonstrate a transition in deformation mechanisms in the range of 100–150 MPa applied stress. This is associated with changes in dislocation–precipitate interactions. Relevant deformation
Liu Yang, Aparajita Pramanik, Sandipan Sen, Shubhashis Dixit, Marcel Muench, R. J. Vikram, Daniel Schliephake, Yolita M. Eggeler, Ankur Chauhan, Martin Heilmaier, Alexander Kauffmann   +10 more
wiley   +1 more source

Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A

Advanced Engineering Materials, EarlyView.
The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han, Julian M. Rosalie, Jan Radners, Mauro Madia, Philipp von Hartrott, Birgit Skrotzki   +5 more
wiley   +1 more source

High‐Temperature Nanoindentation of Metals: Assessing Thermal Drift, Frame Compliance, and Chemical Composition Effects on the Reported Mechanical Properties

Advanced Engineering Materials, EarlyView.
Do not let thermal drift and instrument artifacts deceive high‐temperature nanoindentation results. We compare classical Oliver–Pharr and automatic image recognition analyses across steels and a Ni alloy to quantify these effects. Accounting for artifacts reveals systematic softening with temperature, while Cr and Ni additions boost resistance ...
Velislava Yonkova, Steffen Brinckmann, Ruth Schwaiger   +2 more
wiley   +1 more source

Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites

Advanced Engineering Materials, EarlyView.
Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter, Andreas Bezold, Johan Westraadt, Katharina Fiegl, Subham Chattoraj, Benjamin Wahlmann, Carolin Körner, Michael Mills, Mathias Göken, Steffen Neumeier   +9 more
wiley   +1 more source

Current Status and Challenges in Data Collection for Aerospace Coatings Deposited by Plasma Spraying

Advanced Engineering Materials, EarlyView.
An innovative approach has been integrated into the GRENAT project to optimize plasma spraying and coating performance. Raw materials are accelerated and melted in the plasma generated by torches, creating coatings. Monitoring sensors collect process data which are combined with ex situ characterization data.
Lila Randriamananjara, Vincent Rat, Quentin Dubreuil, Patrice Valorge, Simon Goutier, Alain Denoirjean, Olivier Messe, Céline Ruelle, Jean‐Philippe Poli   +8 more
wiley   +1 more source

Workflow for Design of Experiments‐Based Modeling of Species Transport and Growth Kinetics in GaN Hydride Vapor Phase Epitaxy

Advanced Engineering Materials, EarlyView.
A novel workflow for investigating hydride vapor phase epitaxy for GaN bulk crystal growth is proposed. It combines Design of experiments (DoE) with physical simulations of mass transport and crystal growth kinetics, serving as an intermediate step between DoE and experiments.
J. Tomkovič, G. Lukin, H. Torkashvand, A. Kerschbaum, M. Müller, S. Besendörfer, J. Heitmann, J. Friedrich   +7 more
wiley   +1 more source

Enhanced Strength and Corrosion Resistance of Ti‐13Nb‐12Ta‐10Zr‐4Sn Alloy by Aging Treatment

Advanced Engineering Materials, EarlyView.
This work systematically investigates the effect of aging treatment on mechanical properties and corrosion behavior of vacuum arc‐melted Ti‐13Nb‐12Ta‐10Zr‐4Sn alloy. Owing to the increased α″ martensite, strength and corrosion resistance were significantly enhanced by aging treatment.
Yuhua Li, Rong Zhao, Qian Zhang, Haojie Wang, Yujing Liu, Lai‐Chang Zhang   +5 more
wiley   +1 more source

Direct Metal Deposition of Graphene–Ti28Nb35.4Zr Matrix Composites With Enhanced Mechanical, Corrosion, and Biocompatibility Properties for Bone Implants

Advanced Engineering Materials, EarlyView.
Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir, Jixing Lin, Yuncang Li, Li Zhu, Paul F. A. Wright, Cuie Wen   +5 more
wiley   +1 more source