Results 81 to 90 of about 1,524,427 (295)

Plastic deformation of dense nanocrystalline yttrium oxide at elevated temperatures [PDF]

, 2012
Nanocrystalline yttrium oxide, Y2O3 with 110 nm average grain size was plastically deformed between 800 ◦C and 1100 ◦C by compression at different strain rates and by creep at different stresses. The onset temperature for plasticity was at 1000 ◦C. Yield
Estournès, Claude, Gallardo-López, Angela, Domínguez-Rodríguez, Arturo, Chaim, Rachman, Marder, Rachel   +4 more
core   +1 more source

Sub‐Nanometer Cobalt on Tungsten Titanium Carbide MXene (W2TiC2Tx): An Electrocatalyst for Highly Efficient and Stable Alkaline Hydrogen Evolution at Industrial‐Scale Current Density

Advanced Materials, EarlyView.
A novel W2TiC2Tx MXene prepared through a MAX‐phase route supports sub‐nanometer Co for highly efficient alkaline hydrogen evolution. Strong Co–W interfacial interactions optimize hydrogen adsorption and catalytic activity, enabling low overpotentials of 63 mV at 10 mA cm−2, small Tafel slope of 44.3 mV dec−1, and exceptional durability at industrially
Xiaopeng Liu, Fan Yang, Deep M. Patel, Mohammad Albloushi, Qiqi Mao, Shan Jiang, Christian J. Breckner, Connor W. Schroeder, Ruoyu Cui, Tao Ma, Dapeng Jing, Wenyu Huang, Jeffrey T. Miller, Wenzhen Li, Luke T. Roling, Yue Wu   +15 more
wiley   +1 more source

Hierarchical Flexible Ceramic Nanofiber Membrane for Simultaneous Membrane Distillation and Photocatalytic Hydrogen Evolution

Advanced Materials, EarlyView.
A hierarchical flexible ceramic nanofiber membrane integrates a La‐stabilized ZrO2 scaffold with superhydrophobic UiO‐66‐NH2/CdS heterojunctions. The gas–liquid–solid interfacial architecture sustains vapor‐selective desalination, visible‐light charge separation, and rapid H2 extraction, enabling simultaneous freshwater production and photocatalytic ...
Pengfei Lin, Xiaochen Lu, Jiawei Sun, Shuai Guo, Xinping He, Chunhai Yi, Zhenyao Wang, Jiaxin Guo, Swee Ching Tan, Alicia Kyoungjin An   +9 more
wiley   +1 more source

Influence of Graphene and Graphene Oxide on Properties of Spark Plasma Sintered Si₃N₄ Ceramic Matrix

Ceramics, 2020
The sintering of ceramic matrix composites is usually carried out by raising the sintering temperature below the melting point of components. Spark plasma sintering (SPS) has the capability to densify ceramics at a relatively low temperature in a very ...
Katalin Balazsi, Mónika Furkó, Piotr Klimczyk, Csaba Balázsi   +3 more
doaj   +1 more source

Preparation of Graphene Nanosheets/Copper Composite by Spark Plasma Sintering

, 2014
Graphene nanosheets(GNS)/copper composite has been prepared by spark plasma sintering (SPS). Microstructure of the sintered composite was characterized using scanning electron microscopy (SEM).
Li, Fangzhi, Hu, Chunfeng, Xie, Rongjun, Qu, D, Wang, Qian, Zhou, Tianliang, Qu, Dong, Zhang, Haibin   +7 more
core   +1 more source

Spark Plasma Sintering of Boron Carbide Powder [PDF]

, 2018
The results presented in this article demonstrate that boron carbide ceramics of a perfect microstructure, of a high density (up to 99.8%) and microhardness (36.1 GPa) can be made from the industrial micron fraction powder thanks to spark plasma ...
Grigoryev, E G, Kazakova, V N
core   +1 more source

Toward Pore‐Engineered 3D‐Printed Materials for Sorption Water Harvesting, Interfacial Evaporation, and Radiative Cooling

Advanced Materials, EarlyView.
Water harvesting, radiative cooling, and interfacial solar evaporation are fundamentally governed by coupled heat, mass, and light transport processes. These processes are mediated by pore architecture, including pore size, connectivity, and hierarchical organization.
Dejan J. Trajkovski, Higgins M. Wilson, Abdallah Y. M. Ali, Jiaxing Xu, Ruzhu Wang, Primož Poredoš   +5 more
wiley   +1 more source

On the Structural and Chemical Homogeneity of Spark Plasma Sintered Tungsten

Metals, 2019
Tungsten-based materials are the prime candidate plasma-facing materials for future fusion reactors, such as DEMO. Spark plasma sintering is a prospective fabrication technology with several advantageous features.
Jiří Matějíček, Monika Vilémová, Jakub Veverka, Jiří Kubásek, František Lukáč, Pavel Novák, Dalibor Preisler, Josef Stráský, Zdeněk Weiss   +8 more
doaj   +1 more source

The Evolution of Aerosol Jet Printing, A Review: Enhancing Material Versatility and Improvements for Next‐Generation Applications

Advanced Materials Technologies, EarlyView.
Aerosol Jet Printing (AJP) has emerged as a versatile additive manufacturing technique for high‐resolution, conformal, and multi‐material printing. This review highlights advances in printable materials, substrate compatibility, post‐processing, characterization, and process innovations, while critically discussing current challenges and future ...
Chandrachur Chatterjee, Rocco Lupoi, Michael J. Gibbons   +2 more
wiley   +1 more source

Silicon Carbide Ceramics for Armor Applications: A Review of Sintering Methods and Additive Systems

Molecules
Silicon carbide (SiC) ceramics are among the most attractive materials for lightweight armor because they combine low density (3.0–3.2 g/cm3), high hardness, and high thermal and chemical stability; however, their densification remains challenging ...
Dauren Zhambakin, Madi Abilev, Almira Zhilkashinova, Aigerim Ichshanova, Leszek Łatka   +4 more
doaj   +1 more source