Results 141 to 150 of about 172,705 (282)

Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V

Advanced Engineering Materials, EarlyView.
Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena, Benjamin Bergmann, Michael Zenger   +2 more
wiley   +1 more source

Assessing Altered Coating Adhesion on Plasma‐Deoxidized Surfaces Under Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
This study demonstrates the effectiveness of atmospheric pressure plasma pretreatment in modifying silicon and stainless steel surfaces to improve adhesion. Argon‐hydrogen plasma increases surface roughness and improves adhesion strength, whereas pure argon results in smoother surfaces and structural changes.
Selina Raumel, Lara Kuhr, Khemais Barienti, Sebastian Herbst, Florian Nürnberger, Hans Jürgen Maier, Marc C. Wurz   +6 more
wiley   +1 more source

Editorial: Training and testing in climbing

Frontiers in Sports and Active Living, 2022
Vidar Andersen, Jiří Baláš, Michail Lubomirov Michailov, Atle Hole Saeterbakken   +3 more
doaj   +1 more source

Low‐Angle Grain Boundaries and Re‐Segregation in Single‐Crystalline Ni‐Base Superalloys

Advanced Engineering Materials, EarlyView.
This work demonstrates that Re‐segregation at low‐angle grain boundaries (LAGBs) in Ni‐base superalloys is influenced by misorientation angle. Advanced microscopy and atom probe tomography reveal that higher misorientation angles increases Re‐segregation.
Alireza B. Parsa, Aparna Saksena, Alesander Kostka, Pascal Thome, Felicitas Scholz, Alexandre Mussi, Christoph Somsen, Baptiste Gault, Jan Frenzel, Gunther Eggeler   +9 more
wiley   +1 more source

Corrosion and Process Analysis of a Preoxidized MgO Recyclate‐Based Cermet Anode in Laboratory‐Scale Na‐Cryolite Molten Salt Electrolysis of Aluminum at 1000°C

Advanced Engineering Materials, EarlyView.
EDX elemental map of the pre‐oxidized MgO–steel cermet anode cross section after electrolysis. The development of inert anodes for aluminum electrolysis remains challenging due to the high corrosivity of cryolite‐based melts at 950°C–1000°C. This study investigates the corrosion and process behavior of a carbon‐free MgO–steel cermet anode derived from ...
Alexander Adamczyk, Farhan Hossain, Felipe A. Garcia Paz, Serhii Yaroshevskyi, Felix Drechsler, Daniel Vogt, Christos G. Aneziris, Alexandros Charitos   +7 more
wiley   +1 more source

Interaction of MgO Recyclate‐Based Cermet Anode With KF‐AlF3‐Al2O3 at 800°C During Laboratory Scale Aluminum Molten Salt Electrolysis

Advanced Engineering Materials, EarlyView.
A carbon‐free, as‐sintered MgO–steel cermet anode, fabricated via cold isostatic pressing using MgO–C refractory recyclate, was evaluated under laboratory‐scale K‐cryolite electrolysis at 800°C. Operation at this reduced temperature, combined with the electrolyte's limited electrical conductivity, led to an increase in cell voltage.
Farhan Hossain, Alexander Adamczyk, Felipe Alejandro Garcia Paz, Serhii Yaroshevskyi, Felix Drechsler, Daniel Vogt, Christos G. Aneziris, Alexandros Charitos   +7 more
wiley   +1 more source

Numerical Modeling of Tank Cars Carrying Hazardous Materials With and Without Composite Metal Foam

Advanced Engineering Materials, EarlyView.
Large‐scale puncture models consisting of hazardous materials (HAZMATs) tank car with protective steel–steel composite metal foam (S–S CMF) are solved numerically. Tank car plate with added 10.91–13.33 mm thick S–S CMF layer does not puncture. Protective S–S CMF absorbs impact energy, reduces plate deformation, and prevents shear bands formation ...
Aman Kaushik, Afsaneh Rabiei
wiley   +1 more source

Affecting the Properties of Copper–Graphene Electroconductive Composite by Severe Plastic Deformation

Advanced Engineering Materials, EarlyView.
Copper‐based composites enhanced with carbon feature convenient mechanical properties and favorable electric conductivity. Processing via deformation and thermomechanical treatments can introduce advantageous microstructures further enhancing their performance. Herein, copper–graphene powder‐based composites are directly consolidated via rotary swaging
Radim Kocich, Lenka Kunčická, Pavel Czernek, Zifan Wang   +3 more
wiley   +1 more source

Understanding the Stochastic Nature of Process Parameter Development of Blown Powder Laser Beam Directed Energy Deposition Additive Manufacturing of Pure Molybdenum

Advanced Engineering Materials, EarlyView.
Identified through the use of statistical design of experiments and metallographic investigation, this study exposes the stochastic origins of intergranular cracks in blown powder laser beam directed energy deposition additive manufacturing of pure molybdenum. It further demonstrates a successful crack mitigation approach with direct correlation to the
Nathaniel J. Lies, Daniel E. Driemeyer, Aaron P. Stebner   +2 more
wiley   +1 more source

Performance Insights in Speed Climbing: Quantitative and Qualitative Analysis of Key Movement Metrics. [PDF]

Bioengineering (Basel)
Pandurević D, Draga P, Sutor A, Hochradel K.   +3 more
europepmc   +1 more source