Results 141 to 150 of about 459 (186)

Review on logarithmic spiral bevel gear

Journal of the Brazilian Society of Mechanical Sciences and Engineering, 2020
Logarithmic spiral bevel gear (LSBG) has received increasing attention among industry and academy in the past four decades. This paper attempts to survey and summarize the recent research and development of LSBG, provides comprehensive references for researchers concerning with this topic and helps them identify further research topics.
Jianfeng Jiang, Qingsheng Luo, Liting Wang, Lijun Qiao, Minghao Li   +4 more
openaire   +1 more source

Virtual Simulation Machining on Spiral Bevel Gear with New Type Spiral Bevel Gear Milling Machine

2009 International Conference on Measuring Technology and Mechatronics Automation, 2009
Spiral bevel gear milling machine is one typical representative of complex manufacturing equipments, it is important for the mechanical manufacturing industry to improve the spiral bevel gear milling machine’s manufacturing capacity. One virtual simulation machining model of new type spiral bevel gear milling machine is set up with the simulation ...
Yanwei Xu, Lianhong Zhang, Wei Wei, Leping Wang   +3 more
openaire   +1 more source

Kinematical Optimization of Spiral Bevel Gears

6th International Power Transmission and Gearing Conference: Advancing Power Transmission Into the 21st Century, 1992
Abstract Kinematical optimization and sensitivity analysis of circular-cut spiral bevel gears are investigated in this paper. Based on the Gleason spiral bevel gear generator and EPG test machine, a mathematical model is proposed to simulate the tooth contact conditions of the spiral bevel gear set.
Zhang-Hua Fong, Chung-Biau Tsay
openaire   +1 more source

Spiral Bevel Gears and Hypoid Gears

2020
In this chapter, the geometry of the main types of spiral bevel gears is first defined and considerations about the spiral angle are made. The corresponding cutting processes are then briefly described, and the generation of active flank surfaces of the teeth is defined.
openaire   +1 more source

Dynamics of spiral bevel gear rattling system

2010 International Conference on Mechanic Automation and Control Engineering, 2010
A non-smooth spiral bevel gear rattling model with backlash was established by considering input shaft angle excitation and normal transmission error. Based on the Poisson's impact law, the oblique-impact process was analyzed in which friction was considered between gear teeth, and the relation between the pre-impact state and the post-impact one was ...
null Jianjun Yang, null Kai Xu, null Xiaozhong Deng, null Bingyang Wei   +3 more
openaire   +1 more source

Original Research on Logarithmic Spiral Bevel Gear

Applied Mechanics and Materials, 2011
In this article, logarithmic spiral curve is successfully applied to bevel gear transmission and used as dentiform line of helicoid bevel gear. Put forward a novel logarithmic spiral bevel gear drive. Because spiral angle on each point of logarithmic spiral curve is constant, the problem of variational spiral angle is solved faultlessly.
Hong Bo Yan, Qiang Li, Zi Liang Wei, Shu Qin Wu   +3 more
openaire   +1 more source

Logarithmic Spiral Bevel Gear Tooth Contact Inspection

Applied Mechanics and Materials, 2010
Introduction of spiral bevel gear tooth contact detection method, detection method based on the principle of EPG in the Y9550-type bevel gear roll tester on a pair of spiral bevel gear tooth contact area of sample detection experiment, obtained by experiment logarithmic spiral bevel gear contact area of the location, shape and size of the result.
Qiang Li, Wen He, Hong Bo Yan, Hong Xiang Zhang   +3 more
openaire   +1 more source

Load Distribution in Spiral Bevel Gears

Journal of Mechanical Design, 2006
Abstract A new approach for the computerized simulation of load distribution in mismatched spiral bevel gears with point contact is presented. The loaded tooth contact is treated in a special way: it is assumed that the point contact under load spreads over a surface along the “potential” contact line (Simon, 2006, Mech.
openaire   +1 more source

Synthesis of contact-optimal spiral bevel gears

Russian Engineering Research, 2015
The influence of gear synthesis parameters used in Expert software on the shape and size of the contact pattern and on the contact pressure is analyzed. An algorithm is proposed for identifying the shape of the lateral tooth surfaces that minimizes the contact pressure in a specified transmission.
V. I. Medvedev, D. S. Matveenkov, A. E. Volkov   +2 more
openaire   +1 more source