Results 71 to 80 of about 1,153 (219)
Modulation Signal Bispectrum Based Monitoring of Tooth Surface Wear for Modification Spiral Bevel Gear [PDF]
, 2020 As the contact point and contact path seriously affect the spiral bevel gear mesh characterize, the tooth modification method was applied to manufacture, and tooth contact markers can verify the contact area.
Gu, Fengshou +11 more
core +1 more source
Jixie chuandong, 2013 For small-module spiral bevel gear,a new machining process is proposed.The pinion is adopted traditional double-side machining method.Designing gear machining parameters,the gear two tooth surfaces are controlled separately to suit for pinion tooth ...
张华, 刘高杰, 徐林林, 马江民
doaj
Chemistry – A European Journal, Volume 30, Issue 2, January 8, 2024.A stereochemical approach to transmitting the directional double‐bond rotary motion of light‐driven molecular motors through space onto a remote single‐bond axis is put forth and successfully tested by means of quantum‐chemical modeling. A key result in the assessment of the approach is that the desired photogearing process is favorable compared to the
Enrique M. Arpa +2 more
wiley +1 more source
Meshing Theory of Circular Arc Profile Spiral Bevel Gear based on Form Method Machining [PDF]
, 2019 The application of numerical control forming method machining in circular arc profile bevel gear is discussed, it is proved that the circular arc profile spiral bevel gear based on this method conforms to the basic law of tooth profile meshing, and the ...
He Zhiwei Duan Jianzhong
core +1 more source
Experimental and computational study of convective heat fluxes in swirling two‐phase flows
Heat Transfer, Volume 53, Issue 1, Page 259-276, January 2024.Abstract The convective mode of heat transfer is mainly due to the bulk motion of the fluid. Its turbulent nature and enhanced heat transfer coefficients have always attracted the academic, scientific community, and industrialists for many decades.
Aitazaz Hassan +5 more
wiley +1 more source
Finite element modelling and load share analysis for involute worm gears with localised tooth contact [PDF]
, 2001 A new approach has been developed by the authors to estimate the load share of worm gear drives, and to calculate the instantaneous tooth meshing stiffness and loaded transmission errors. In the approach, the finite element (FE) modelling is based on the
Gentle, CR, Su, D, Yang, F
core
The Measurement and Evaluation Method of Global Error of Spiral Bevel Gear [PDF]
, 2011 This paper offers a method of spiral bevel gear’s global error measurement and evaluation based on three-coordinate measurement according to the characteristics of spiral bevel gear.
Piao Sheng, Hua Zhao
core +1 more source
Research of the Tooth Flank Design and Movement Simulation of Spiral Noncircular Bevel Gear
Jixie chuandong, 2017 Applied the theory of curve and surface of differential geometry,based on the noncircular bevel gear profile researched and developed successfully by research team. The construction principle of the tooth section line of the spiral noncircular bevel gear
Xu Aifen, Jia Jumin, Chen Yuqing
doaj
Analysis of Vibration Characteristics of Hydraulic Excavator Device Under Flat Ground Conditions
Modelling and Simulation in Engineering, Volume 2024, Issue 1, 2024.Hydraulic excavators, characterized by their high efficiency and versatility, are crucial equipment in engineering construction. During the automatic excavation process, the excavator may experience resonance phenomena, which can affect the stability of the entire system.
Kailei Liu +6 more
wiley +1 more source
Topology Optimization of Spiral Bevel Gear for Differential
International Journal of Innovative Technology and Exploring Engineering, 2020 The Spiral Bevel gear used in differential should be enough stiff to resist the vibrations and stresses encountered during its operation. The gear must also have sufficient strength to bear the bending stresses occurring in the differential assembly in its course of operation.
Mit Patel +4 more
openaire +1 more source