Results 41 to 50 of about 207,947 (242)
Synthesized Cu (In, Ga) Se2 (CIGS) thin films and implementation as the active light absorbing material in photovoltaic devices (PVs) [PDF]
Engineering and Technology Journal, 2015 This review article summarizes our research focused on Cu(In, Ga)Se2 (CIGS) nanocrystals, including their synthesis and implementation as the active light absorbing material in photovoltaic devices (PVs).
Omar A. Ali +5 more
doaj +1 more source
Aesthetic Surgery Journal, 2005 The modern formulation of dihydroxyacetone (DHA), the only sunless tanning solution approved by the Food and Drug Administration (FDA), is combined with bronzers and moisturizers to deliver a cosmetically acceptable skin color and a natural-looking tan without ultraviolet (UV) exposure.
openaire +2 more sources
Advanced Engineering Materials, EarlyView.Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios +5 more
wiley +1 more source
Materials Research Express, 2020 In this work, the influences of welding speed on microstructure and mechanical properties in friction stir welding (FSW) of the hot-rolled Al-9.2Mg-0.8Mn-0.2Zr-0.15Ti alloy plates has been investigated.
Yingli Li +6 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal +2 more
wiley +1 more source
Journal of Materials Research and TechnologyAluminum alloys (Al) produced by fusion-based additive manufacturing techniques exhibit limited strength due to undesirable grain growth, porosity, and thermal gradient.
Anil Lama +5 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.New features on yttria‐stabilized zirconia after exposure at 1500°C: Newly discovered pyramidal structures on an old material. After exposure at 1550°C on the cross section of YSZ new features, namely pyramidal structures are discovered. These structures grow with time, increase in numbers, appear as singularities, are often arranged in strings, and ...
Doris Sebold +2 more
wiley +1 more source
Spray characteristics of supercritical DME
Nihon Kikai Gakkai ronbunshu, 2020 The penetration of DME spray is shorter than that of diesel fuel when the same injection system is used because DME cannot be injected at high pressure like diesel fuel due to its high compressibility. Chris reported that supercritical gasoline spray has
Ryuhei TAKADA +6 more
doaj +1 more source
Current Status and Challenges in Data Collection for Aerospace Coatings Deposited by Plasma Spraying
Advanced Engineering Materials, EarlyView.An innovative approach has been integrated into the GRENAT project to optimize plasma spraying and coating performance. Raw materials are accelerated and melted in the plasma generated by torches, creating coatings. Monitoring sensors collect process data which are combined with ex situ characterization data.
Lila Randriamananjara +8 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar +7 more
wiley +1 more source