Results 61 to 70 of about 90,455 (268)

Experimental Study on Biodiesel Injection Characteristics and Spray Development Tendency

Applied Sciences
The conversion of biodiesel’s chemical energy into mechanical work in diesel engines is strongly influenced by the formation and quality of the fuel–air mixture.
Boban Nikolić, Breda Kegl, Dragan Marinković, Nikola Petrović, Vesna Jovanović   +4 more
doaj   +1 more source

Experimental Characterization and Constitutive Modeling of the Effect of Prior Inelastic Strain on the Viscoplastic Behavior of AD730 at 700 °C

Advanced Engineering Materials, EarlyView.
This study shows that superalloys used in aircraft engine disks become much more prone to deformation at high temperatures if they have been strained during manufacturing. This effect increases with the level of prior strain but eventually reaches a limit.
Fabio Machado Alves da Fonseca, Patrick Villechaise, Malik Durand, Arnaud Longuet, Florent Coudon, Loïc Signor, Julien De Jaeger, Dominique Eyidi, Nathalie Bozzolo, Jonathan Cormier   +9 more
wiley   +1 more source

Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading

Advanced Engineering Materials, EarlyView.
This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev, Noah‐Lean Roschlaub, Anne Jung   +2 more
wiley   +1 more source

Three-Dimensional Analysis of Pressure Swirl Injector Based on Trumpet Effects and Orifice Length Variations [PDF]

Iranian Journal of Chemistry & Chemical Engineering
This research studies the pressure swirl injector’s internal and external flow under adiabatic and incompressible assumptions. A transient three-dimensional flow simulation has been employed.
Adel Makhdoum, Seyed Mahdi Mirsajedi
doaj   +1 more source

Multilayer Self‐Limiting Electrospray Deposition via Stepped Voltage Bias

Advanced Engineering Materials, EarlyView.
Self‐limiting electrospray deposition (SLED) uses a high voltage to generate and deposit a charged payload on a target surface. The coating retains its charge, repelling newly arriving material. SLED thickness can be decreased by applying a secondary bias to the target.
Madhuri Deb, S. Rahman Pejman, Alexander Jakimowicz, Jonathan P. Singer   +3 more
wiley   +1 more source

Spray and droplets characteristics of air assisted nozzle under extreme low fuel temperature [PDF]

EPJ Web of Conferences
To extend the range of unmanned aerial vehicles (UAVs), internal combustion engines using aviation kerosene are utilized because of its high efficiency and power density.
Fang Yuwen, Huang You, Ma Xiao, Xu Lubing, Sheng An, Tang Zhong, Shuai Shijin   +6 more
doaj   +1 more source

Composites of Shellac and Silver Nanowires as Flexible, Biobased, and Corrosion‐Resistant Transparent Conductive Electrodes

Advanced Functional Materials, EarlyView.
Shellac, a centuries‐old natural resin, is reimagined as a green material for flexible electronics. When combined with silver nanowires, shellac films deliver transparency, conductivity, and stability against humidity. These results position shellac as a sustainable alternative to synthetic polymers for transparent conductors in next‐generation ...
Rahaf Nafez Hussein, Tiago Carneiro Gomes, Eliza Ng, Simon Rondeau‐Gagné, Tricia Breen Carmichael   +4 more
wiley   +1 more source

Experimental Study of Spray and Combustion Characteristics in Gas-Centered Swirl Coaxial Injectors: Influence of Recess Ratio and Gas Swirl

Aerospace
The spray and combustion characteristics of a gas-centered swirl coaxial (GCSC) injector used in oxidizer-rich staged combustion cycle engines were analyzed.
Jungho Lee, Ingyu Lee, Seongphil Woo, Yeoungmin Han, Youngbin Yoon   +4 more
doaj   +1 more source

From Food to Power: Hydrogel Thermoelectrics for Ingestible Electronics

Advanced Functional Materials, EarlyView.
We introduce a fully edible thermoelectric–electrochromic platform that harvests heat from food and converts it into a visible color change. N‐type and p‐type hydrogel thermoelectric generators connected in series power anthocyanin‐based electrochromic displays, demonstrating the feasibility of safe, biodegradable, ingestible systems for on‐food ...
Antonia Georgopoulou, Bokeon Kwak, Dario Floreano, Esther Amstad   +3 more
wiley   +1 more source

Transparent Deformable Thin Film Electric Heater for Stable and Accurate Control of High Temperatures

Advanced Functional Materials, EarlyView.
Au/GaOx‐based transparent heaters combine high optical transmittance and low sheet resistance with exceptional thermal stability up to 521°C for over 6 h. The interfacial GaOx layer suppresses dewetting of Au and enhances adhesion, ensuring mechanical robustness during deformation and reliability for real‐world applications including grilling ...
Younghyun Lee, Huisim Moon, Yeongseo Jin, Woosung Cho, Geonwoo Kim, Gihyeok Eom, Michael D. Dickey, Minsik Kong, Unyong Jeong   +8 more
wiley   +1 more source